An 18.5 m long shaft ABC consists of two sections AB and BC with diameters 150 mm and 200 mm respectively as shown in Fig. Q2. Draw the torque diagram for the shaft. If modulus of rigidity of the material of the shaft is 9 x 10* N/mm? for section AB and 10 x 10* N/mm? for section BC, calculate the angle of twist at B and C. 8 kNm A 5 kNm 10 m- 8.5 m 7/9

An 18.5 m long shaft ABC consists of two sections AB and BC with diameters 150 mm and 200 mm respectively as shown in Fig. Q2. Draw the torque diagram for the shaft. If modulus of rigidity of the material of the shaft is 9 x 10* N/mm? for section AB and 10 x 10* N/mm? for section BC, calculate the angle of twist at B and C. 8 kNm A 5 kNm 10 m- 8.5 m 7/9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the %3D torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m A 8 kN-m LAB B T LBC.
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation Ø, at the cross section where the torque To is applied. 0.75 in. 3.0 in. A 4000011Ww То 6.0 15.0 in. 2.4 3.0 0.75 in. in. in.
Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm Y-face 50 X-face D= 40 mm. 30MN m2 30 50 MN m-
Question 6 Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. a. Determine the maximum value of shear stress developed and the angle of twist if a Torque of 2 kNm is applied at A b. Determine the maximum torque that can be applied at A when the maxımum shear stress is 75 MPa and angle of twist at A is 0.02 rad. 600 mm 600 mm 90 mm 30 mm 90 mm Figure Q6
Question 2: The young modulus of the shaft shown in figure below is 80 GPa. Diameter of the shaft AB (part 1) is 55 mm and for shaft BC (part 2) is 40 mm. knowing that the allowable shear stress is 458.5MPa and angle of twist at point c is 3º. Calculate the maximum torque that can be transmitted at point c. (2) Tc B |C 0.8 m 1.2 m
QUESTION 2) The shaft, first two meters length has a solid cross-section with a diameter of 6 cm and the last one meter length has a hollow cross-section with a inner diameter 5 cm and outer diameter of 6 cm is shown in the figure. If the allowable shear strength tu-35 MPa and shear modulus G=200 GPa, determine the allow magnitude of the torsional moment M for a safe structural system. M M бст IScm B C D lm Im 1m
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid eircular cross section and segment CB having hollow eircular cross section. If the shafts material is steel with shear mođulus G = 11 x 10 psi, and the torque is T, = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied. 0.75 in. 3.0 in. -15.0 im. OF F 2.4 3.0 0.75 in. in.
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
The system under the effect of torsion;a- Draw the torsional moment diagram.b- Determine the torsion angle CA (rotation angle) that will occur at point C.c- Determine the load shear stress.(G=80 000 MPa M1=5000Nm M2=4000Nm D1=120mm D2=90 D3=80 D4=60
To (a) Find the forsional stiffness of the chanel section Shown, Polov (STIDEES ridots WON (6) consider a structure for which +₁ = 3/4 inch, t₁ = 1/2 inch, 6=4 inches, a = 6 inches and G = 3X107 psi. Determine the angle of twist per unit length when the structure is subjected to a torave of 25,000 1b-ins. C) If the total length of the structure of Part (b) is 6ft, and the shaft is fixes at one end, determine the maximum angle of twist. What is the angle of twist at half-span?
Q.4) A pipe assembly is acted on by four forces and one couple moment. The 300 N force is parallel with the z-axis, the 130 N force is parallel with the y-axis, and the 60 N force is parallel with the x-axis. Force F, has a magnitude of 220 N and coordinate direction angles given by aA = 45°, BA = 60°, and YA = 120°. The couple moment M, is in the x-z plane and has a magnitude of 400 N-m. Determine the resultant moment about point B. Mc 30 300 N 1 m B0.5 m 0.75 m 0.75 m 130 N FA
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft