Along a galvanized iron pipe (ε=0.15 mm) of 30 cm in diameter, pump 60 lps of oil; µ = 0.016 N s/m2 and γ = 8535 N/m3 If each of the pumps used produces 49 N/cm2 of rise in pressure; determine the distance they must plant the bombs.

Q: ) For a long triangular groove shown in figure, calculate viewfactor F12 and F13. a 27 32 b

A:

Q: (3) In a counter flow heat exchanger if AT = AT, show that ATAT = AT. AT is the log mean temperature…

A:

Q: A gas is compressed isentropically from 120 psia, 3.5 cubic feet per seconds and 40 deg F to 325…

A:

Q: Q2.A/ Show that the expression (1/2 mv² = √mgh) is dimensionally correct, where v is the velocity…

A:

Q: A B

A:

Q: Let the pressure in the cylinder shown below be a function of volume such that P = C/V (where C is a…

A: Work is said to be done by the system if the sole effect to the things external to the system gets…

Q: What material corresponds to the microstructure of part f? Answer Choice Group 10110 steel Steel…

A: Given: There are different types of images given in which the image shown in the part f which is of…

Q: 6. Find the C.O.P. of a refrigeration system if the work input is 30 KJ/kg and refrigeration effect…

A: Given, Work input to the refrigeration system = W = 30 kJ/kg Refrigeration effect = Q1 = 120 kJ/kg…

Q: Give the answer with proper explanation why you chose that specific option. Thank you

A: Given: Here is the torque curve is shown here, To find: Determine the representation of Torque…

Q: The temperature at which oil will release sufficient vapor to support combustion continuously for…

A: Option 5 : Fire point

Q: Example 5-1 on EGT The following figure shows an epicyclic gear train (EGT) having two inputs. The…

A:

Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…

A:

Q: Dimensional analysis can be used in problems other than fluid mechanics ones. The important…

A: T=fcnl,I,E,ρ,σ

Q: The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade…

A:

Q: A wedge assembly, composed of wedges X and Y, is designed to lift crate W whose weight is 1936 N, as…

A: Given data Weight of block = 1936 NCoefficient of friction = µ = 0.0875We have to draw the free body…

Q: A wedge assembly, composed of wedges X and Y, is designed to lift crate W whose weight is 1936 N, as…

A: Given data Weight of crate W = 1936 N Coefficient of friction on each surface = 0.0875  We have to…

Q: Define boundary layer and explain the fundamental causes of its existence.

A: Introduction: BOUNDARY LAYER: A boundary layer is a thin layer of fluid created by the fluid flowing…

Q: . A main shaft has 100mm diameter is running at 350rpm, what power could be delivered by the shafts?

A:

Q: QUESTION 10 A Watt (W) is defined as one Joule (J) of energy per second (s): 1 W = 1 J/s. It is also…

A: The maximum range of the car is 326.1 miles.

Q: The industrial truck is used to move the solid 1200- k roll of paper up the 30° incline. If the…

A: Given data as per the question Mass of roller =1200 kgcofficient of friction =0.40

Q: [3 4].[51]= Not exist O [154] O [12] O [13] O [11]

A: Given question: We have two vectors [ 3 4] and [5 1] We have determine the output of the operation […

Q: ...The rating life at 90% reliability for a ball bearing is 15 x 106 revolutions. If the bearing is…

A:

Q: A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water…

A:

Q: (iv) Show that the Kelvin-Planck and the Clausius expressions of the second law are equivalent.

A: To Show:-  Kelvin-Planck and Clausius expressions of the second law are equivalent.

Q: triangular open-channel

A: tan θ=HVθ=tan-134=36.87o A=area of ∆ ABC=2 area of ∆ABDA=2*AD*BD2=AD*BDA=BD*tan 36.87*BD           ∵…

Q: Determine the reactions of the beam using Force Method Analysis. Set A is fixed, B is roller and w =…

A:

Q: A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen 4.8%,…

A:

Q: The efficiency of a Carnot cycle is 80%. If the cycle direction is reversed, the COP of reversed…

A: Given that, Efficiency of Carnot cycle = 80 % To Find: COP = ?

Q: The car slows down at constant acceleration of 4 m/s^2 from the velocity of 40 m/s. Detemine the…

A:

Q: surface condenser

A: Absolute pressure Pt=(765-715)*10-3*.0135951*106*9.81=6668.396 N/m2Pt=6.67 kPa Partial pressure of…

Q: Determine the maximum mass (kg) that can be lifted at E if the 10-HP motor A has a maximum rotation…

A: Given: The power, P = 10 HP The speed of the shaft at motor, N = 300 rpm The diameter of AB, d = 10…

Q: If the gauge pressure far away from the origin is zero, what is the pressure at the origin?

A:

Q: The power transmitted by a belt drive is proportional to the Tension as follows P = Tv _wv² Find…

A: Given    P = Power    g = Gravity    v = Velocity Find   Expression for velocity

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A:

Q: What is the change in internal energy of air (assumed to be an ideal gas) cooled from 1000°F to…

A: given data  Ideal gas m = 1 kg T1 = 1000°F T2 = 200°F For ideal air  Cv = 1.003 KJ/KgK So…

Q: Two identical slender rods AB and BC (MAB = mBc = 1.5 kg) are welded together to form an L shaped…

A:

Q: Temperature differences for Thermal efficiencies do not have to be converted to absolute…

A: If the thermal efficiencies of a cycle is expressed in terms of temperature difference, then it is…

Q: Consider the steady, two-dimensional velocity field given by V=(1.3+2.8x)/+(1.5-2.8y)/ Determine;…

A: Determine:   (i) the fluid speed at origin;   (ii) the location of stagnation point in the flow; and…

Q: Which of the following is not an extensive property? A. length B. melting point C. volume D.…

A: Which of the following is not an extensive property? Answer: B. melting point

Q: Determine the maximum mass (kg) that can be lifted t E if the 10-HP motor A has a maximum rotation…

A:

Q: (B) A vertical cylinder 1.5m height and 18 cm in diameter is maintained at 100°C in an atmosphere…

A: Answer: The heat loss by free convection: 1173.22 W

Q: Where can I find the shell option in AutoCAD 3D Modify, solids editing O All option Solid, solids…

A:

Q: Problem 2: The activity details and their predecessors are given below along with their activity 1…

A: Network diagram  A network diagram in project management represents the duration of project…

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA.…

A: Introduction: The force acting on an object can be divided into two components one perpendicular to…

Q: Which of the moment equilibrium equations is CORRECT? A. +6 ΣΜΑ = -P sin 30 (0.70) - P cos 30 (1.65)…

A:

Q: Calculate the power in Kw required to drive the second stage of a double-acting two-stage compressor…

A:

Q: At 3MPa and 400C, 2 kg/s steam flows into a turbine. It exits at 300kPa. The turbine has an…

A: Given: T1 = 400 C P1 = 3 MPa P2 = 300 kPa efficiency = 85%

Q: the piston travel, for an engine

A: To find :-  Piston travel

Q: For a given cogeneration plant where Q is the total input energy in kW, WT is the turbine work…

A: Given questions: Explain what is meant by  "cogeneration plant". State examples of industry…

Q: Find the moment of inertia about the z-axis for a constant density 1 circular cone with base radius…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.