About Industrial Pipes and based on a hypothetical industrial piping system: How to estimate corrosion thickness (20 years)? How to calculate the minimum thickness for the pipes of a system? How to inform the schedules based on the thickness (commercial adopted) for the pipes? How to define the pressure class adopted? How do you calculate MAOPs? How to define the opening pressure of the installed safety valves (PSV), based on the operating pressures and MAOP?

About Industrial Pipes and based on a hypothetical industrial piping system: How to estimate corrosion thickness (20 years)? How to calculate the minimum thickness for the pipes of a system? How to inform the schedules based on the thickness (commercial adopted) for the pipes? How to define the pressure class adopted? How do you calculate MAOPs? How to define the opening pressure of the installed safety valves (PSV), based on the operating pressures and MAOP?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter50: Commercial, Packaged Rooftop, Variable Refrigerant Flow, And Variable Air Volume Systems

Section: Chapter Questions

Problem 18RQ: Explain how carbon dioxide levels can be used to estimate the occupancy level in a particular area...

See similar textbooks

Similar questions

What are valid reasons for adding Yttrium to the zirconia in the Thermal Barrier Coating (TBC) in a turbine blade? Select one or more: O a. To match the thermal conductivity of the TBC to the metal substrate b. To avoid breakage during change in thermal conditions O c. To match the thermal conductivity of the TBC to the underlying oxide layer Od. To increase the weight of the TBC O e. To prevent a change of the crystallographic structure as the temperature changes
020 ABOUT INDUSTRIAL PIPING WHAT ARE THE POSSIBLE TRANSIENT OPERATING CONDITIONS FOR PIPING SYSTEMS?
10. Sodium sulfate corrosion is a typical degradation mechanism in: O Centrifugal compressor O Axial compressor Air intake Gas turbine
Q1. Well water contained in an AISI 304 SS pipe network for chemical treatment and posterior distribution by aerial water pipes to different locations in a food manufacturing facility was analysed. The AISI 304 SS pipe network had an approximate 300 m length, 154 mm diameter and 2.0 mm wall thickness. The AISI 304 SS pipes were welded using a Tungsten Inert Gas (TIG) welding procedure. In-situ weld quality assurance was tested by pressurized WW, and no pinhole leakage was detected. After the pipe network remained out of service for 6 months at room temperature containing stagnant, pressurized well water, pitting corrosion was observed on the weld joints and the base material by the presence of multiple pinhole leaks.(a) Discuss, with chemical equations if relevant, TWO corrosion events that may have caused the pitting corrosion.(b) What practical steps could have been taken to mitigate for this potential outcome?(c) Identify corrosion inhibition methods to mitigate for the corrosion…
One of the ways to keep a pipe warm is by means of a steam tracer, through which an electrical resistance is used around the pipe and in a helical shape throughout its diameter?
A nozzle having I.D. 400 mm is fabricated from S.S. 316 plate. It is attached by welding to a vessel having I.D. 1500 mm. Internal design pressure is 10 kgf/cm2 and design temperature is 300oC. Maximum allowable stress at design temperature is 612.4 kgf/cm2. Joint efficiency is 0.85 and corrosion allowance is 1.5 mm for both shell and nozzle. Density of material of fabrication is 7830 kg/m3. Calculate thickness and weight of reinforcement pad
111 about industrial piping WHAT IS THE RELATIONSHIP BETWEEN OPERATING PRESSURES, MAWP, HYDROSTATIC TEST AND OPENING PRESSURE OF PSVs valves?
119 ABOUT INDUSTRIAL PIPING HOW SHOULD LOAD AND ENERGY BALANCE BE DONE IN A BRANCHED PIPING SYSTEM?
Give an example of the Resistance Factor?
What is the difference between mobility and mobility ratio in enhanced oil recovery.
Discuss Kettle-Type Boiler Covering: - Working Boiling point Elevation Temperature drop effect Please write 500 - 600 Words, No Plagiarism
113 About industrial piping UNDER WHAT CONDITIONS SHOULD FLOW VELOCITIES BE LIMITED?