A6x 12-in. plate is subjected to four loads as shown. (a) Replace the given forces with an equivalent force- couple system at C, (b) consider a single force resultant and determine the vertical distance from point C to the point where the line of action of the single force resultant intersects the edge CD. 50 lb 6 in.- 20 lb 40 lb 6 in. F 6 in. 50 lb

A6x 12-in. plate is subjected to four loads as shown. (a) Replace the given forces with an equivalent force- couple system at C, (b) consider a single force resultant and determine the vertical distance from point C to the point where the line of action of the single force resultant intersects the edge CD. 50 lb 6 in.- 20 lb 40 lb 6 in. F 6 in. 50 lb

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.6.7P

See similar textbooks

Similar questions

Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
5 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear s tress of 60 MPa in steel or 40 MPa in alu minum. Use G = 80 GPa for steel and 30 GPa for aluminum. Drawing not included in this problem.(
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
E CH2- Resultant paf - Adobe Acrobat Pro Estended Fle Edit View Document Comments Forms Tools Advanced Windew Help 2/87 If the resultant of the two forces and couple M passes through point O, determine M. 150 mm 60° mm 30 M, = M-400x 0.15cos30-320x0.3 0 M = 148 Nm CCW 320 N 160 400 N mm Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N ahid hamoodi •..
The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider is symmetrical. The bearing stiffeners at supports are the sole means of providing restraint against torsion. Design the bearing stiffeners at supports. with minimum moment of inertia about the center line of web palte only as the sole design criterion. The flat section available are: 250 x 25, 250 x 32, 200 x 28, and 200 x 32 mm. Draw a sketch 500 25 8 .1445 Dimensions in mm 20 +425
4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
C Clego etto Ports Pleese see an aac 105. A member ABCD is subjected to a force system as shown in the figure B C 45+ 365 450 130 The resistive force in the part BC is (a) 365 (compressive) (b) 450 (tensile) (c) 85 (compressive) (d) 320 (compressive)
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
W 72 EI УБ A For the cantilever beam and loading shown, determine Part 1 (a) the equation of the elastic curve for portion AB of the beam, Part 2 out of 3 (b) the deflection at B, 10 wa 3x² W -2a- B - 16 ax down C
f. Calculate the maximum safe load "P" in KN Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Task 12 Z A C B 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed joint bearing in A and a sliding bearing in B and C. Note that the beam is continuous at point B and that the joint in the bearing is below the beam. The beam is subjected to an evenly distributed load q between A and C, while there is a point load F at point D. The beam is made of steel with an E-module E = 210 000 MPa and has a cross section with a second area moment ly = 12x106 mm4. The value of the evenly distributed load q and the length a are determined from: 9= ID+25 20 kN/m ID+40 a= m 50 ID=40 a) Determine how much the maximum force can be when the bearing in point B can withstand a maximum vertical force of 50 kN (Bz< 50 kN). Write your candidate number on all the sheets you upload. b) Now set the force F to the value you found in question a) and decide how big the deflection of the beam will be in point D, under the point load F. Write your candidate number on all the sheets…
De term ine the kin d and am ount of stress in e ach mem ber of the truss shown by the method of jo in ts in figure P 5-2 (page 76).- 1000lb 1000lb 1000lb 1000Ib 1000 Ib U. h = 20 ft 500lb 500 Ib L. L. RAV 6 pane ls at 10' - 6 ft RBy Note: 1. F o llo w strictly the lecture notes g iv en. Draw the FBD of e ach jo in t 2. Sum m a rize and tabu la te your answers. 3. Compu te the bar forces up to member U,L3 on ly because the truss lo a d in g is sym metric aland the bar forces of right sid e members are id en tic al w ith th e left s ide members. But you in c lu de th e rig ht sid e mem bers in have to the tabu la tion. 4. Show the com puta tio n ho w the leng th s were obta in ed. 5. Look for your own data in the table provided. 6. Copy the problem , data of problem and fig ure of the proble m TABULAT ION FOR SUMMAR Y OF COMPUTATION OF BAR FORCES METHOD OF JOINTS (PROBLEM P5-2 PAGE 76) Mem ber Identification Length Bar Forc e Туре of ft Ib force LOL1 10 3750 Tensio n L1L 2 10 Tension…