A. Using an operational amplifier draw the circuit diagram of a noninverting amplifier with a voltage gain of 25. Show all power supply connections, input and output voltages, and give appropriate values for the resistors. B. If the voltage gain is increased to 200, what effect will this change have on the bandwidth of the amplifier and why is this so? C. If the resistance of the transducer connected to the input of the noninverting amplifier is increased from 50 ohms to 50k ohms, what effect will it have on the voltage gain of the amplifier.

A. Using an operational amplifier draw the circuit diagram of a noninverting amplifier with a voltage gain of 25. Show all power supply connections, input and output voltages, and give appropriate values for the resistors. B. If the voltage gain is increased to 200, what effect will this change have on the bandwidth of the amplifier and why is this so? C. If the resistance of the transducer connected to the input of the noninverting amplifier is increased from 50 ohms to 50k ohms, what effect will it have on the voltage gain of the amplifier.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For DAC with resolution of 0.16 volt and to full scale reading of 10 voltages: Design suitable Binary Weighted Resistor DAC and sketch the circuit Design R-2nR DAC and sketch the circuit Calculate the input digital signal and the related output signal at 25% intervals of the full scale voltage value. Calculate the voltage at the ladder points. Put the result fo your calculation in a i. ii. iii. iv. table.
3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive (supply) a load resistance RL. The supply voltages to the op-amp are +15 V and -15 V (not shown). a) What is Vout? b) If R = 1 k 2, what is the smallest R, that the circuit can handle without "sagging" the output voltage? c) What should be the power rating of the resistor R? Be explicit about your assumptions. +15 V R Vout IN4738 CS Scanned with CaScanner
For power amplification of a CLASS A amplifier circuit, the operating point in the output characteristic curve should be located at the of the DC load line. middle end to end point maximum voltage point maximum current point
Sketch the voltage transfer characteristics of an ideal voltage amplifier and a real voltageamplifier. Ensure to label the important regions.
Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
R2 R, 1+ -VEE =- 15 V V. out in R, R1 R1 = 5.6 kQ V out Vin Vcc =+ 15 V Rin 19) calculate the value of R2 required for a closed-loop voltage gain of 5V/V
One of the following is not a property of a common-emitter amplifier: Select one: a. high voltage gain b. No phase inversion c. high current gain d. Emitter is at ac ground
The transistor parameters for the circuit in Figure are B, =B2 = 100, VBE1on) = VBE2ton) = 0.7 V, and %3D VA1 =VA2 =0.Find the small signal voltage gain Av = vo/vs. (Note that V-=0.026 V) Vcc=9 V Rib Q1 Vs 1 ko -Ro 20 V 100 Q -ww
Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
Figure 1(a) shows a series fed class A amplifier circuit. In order to achieve the maximum efficiency, the Q point must be located at the center of the DC load line as shown in Figure 1(b). This generates the maximum output current swing of Icmax (p – p) RC and the maximum output voltage swing is VCEmax(p – p) = Vcc Assume that the maximum input de power is (1 Vcc Pimax(dc) = Vcc!cQ(max)=Vcc \2° Rc. 2Rc Find the maximum efficiency, 7 of this circuit.
Write the expression for the output voltage of a balanced modulator
4. Assume the following data from the Zener diode datasheet: Zener knee current =0.25mA, Zener Max Current=100mA, and max de power dissipation = 1 W, and regulated output voltage = 7.5 V. For the circuit below answer the following questions (a-b): V2 R1 www 1kQ Fig. 3 D2 R2 6 1.