a. A purely reactive load impedance Z₁ =jX terminates a transmission line. Prove that the reflection coefficient magnitude |K| is always unity, assuming the characteristic impedance Zo is real. What is the VSWR of the line in this case? b. Consider the transmission line in the figure. i. Determine the SWR on transmission line ii. The input impedance If=102, find I, in the figure. 100/0° V 20 92 Air, lossless 2-50 92 2.72 40 12 1000 /30 Q

a. A purely reactive load impedance Z₁ =jX terminates a transmission line. Prove that the reflection coefficient magnitude |K| is always unity, assuming the characteristic impedance Zo is real. What is the VSWR of the line in this case? b. Consider the transmission line in the figure. i. Determine the SWR on transmission line ii. The input impedance If=102, find I, in the figure. 100/0° V 20 92 Air, lossless 2-50 92 2.72 40 12 1000 /30 Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
j0.25 For the two coupled branches shown above, Ya =-j0.5, Yb = -j1 & Ym = j0.25. Using Equivalent Admittance, find the admittance located between nodes 2 & 3: O a. j0.25 O b. -j0.25 O c. None of these O d. -j1 O e. -j0.5
6-A lossless T.L. has Zo = 100 N and is loaded by an unknown impedance Its VSWR is 4 and the first voltage maximum is A/8 from the load . Find the load impedance .
The figure shows a 500-kV (line-to-line voltage) transmission line linking two systems. The theoretical maximum power that can be transferred from System A to System B is 5,000 MW, which occurs when the power angle 8 = 90°. The line current is then proportional to (VA - VB) The reactive power losses (Mvar) in the transmission line during this transfer would be most nearly: Wond O A. 1,667 O B.. 3,333 O C. 5,000 O D. 10,000 Know EQUIVALENT SYSTEM A VA= 500 28 KV m XL = 50 Ω EQUIVALENT SYSTEM B VB = 500 40⁰ kV O
2) A 200 ohm resistive load will be matched to a So ohm resstive source impedance. a) Calalate the L-C poss and high pass lumped matching netuwork component Values (tuo sets of L-C vales) b) Sketch the impedonce matching netwark that can be constructed by connec tion of short line segmants. C Assume 15 ohm and 150 ahm characteristic impedance lines are auailable tine lengths for realaing Determine the coriesponding one of the Salutions in part ()
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
A loss less TiL with characteristic impedance of to is terminated in Zr=3Z0. use crank diagram to sketch the voltage versus distance from the load, (Assume vst = 1 volt). @ Repeat the above How for Zv=Zo/3-
A three-phase, 60-Hz, untransposed transmission line runs in parallel with a telephone line for 20 km. The power line carries a balanced three-phase rms current of Ia = 3202 – 240°A. The line configuration is as shown in figure. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage induced in the telephone line. = 32020°A, Ī, = 3204–120°A, and a 4 m 4 m 5 m d G2 mO
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…