A water pump increases the water pressure from 15 psia to 80 psia. a. Determine the flow work, in Btu/lbm, required by the pump. Assume thatthe state of the water at pump inlet is saturated liquid and that the specificvolume remains constant during this process. b. Water enters this pump through a 1.5-in-diameter opening and exitsthrough a 2-in-diameter opening. Determine the velocity of the water at theinlet and outlet when the mass flow rate through the pump is 1.1 lbm/s

A water pump increases the water pressure from 15 psia to 80 psia. a. Determine the flow work, in Btu/lbm, required by the pump. Assume thatthe state of the water at pump inlet is saturated liquid and that the specificvolume remains constant during this process. b. Water enters this pump through a 1.5-in-diameter opening and exitsthrough a 2-in-diameter opening. Determine the velocity of the water at theinlet and outlet when the mass flow rate through the pump is 1.1 lbm/s

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: Air from the discharge of a compressor enters a 1 m³ storage tank. The initial air pressure in the…

Q: A steam turbine is used to generate electric power in a small-scale process industry. The turbine…

A: As per Bartleby guidelines we are allowed to solve only first 3 subparts of a problem. So kindly…

Q: Ammonia steadily flows at 2.64 lbm/s into an adiabatic compressor as a saturated vapor at 30 F and…

A: Given: The mass flow rate of the ammonia, m = 2.64 lbm/s The shaft power, W = 106 Btu/s The pressure…

Q: Sketch T-S diagram process

A: Solution : Given data : P1 = 100 kPa , p2 = 1500 kPa efficiency = 85% ,T1 = 27 degree C Calculation…

Q: Q5: A-Steam enters a turbine with a velocity of 35 m/s and specific enthalpy 2990 kJ/kg. the steam…

Q: Refrigerant-134a enters the compressor of a residential heat pump at 140 kPa at a rate of 216 kg/h…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

A: Option a is correct.

Q: A pump increases the pressure from 10 kPa to 70 kPa. Determine the power input required, to pump 2…

Q: In a gas turbine unit, the gases flow through the turbine at 13 kg/s and the power developed by the…

A: Given data: Mass flow rate of gas (m.)=13 kg/s The power developed by the turbine (P)=14000 kW The…

Q: The mass flow rate of the gas in a gas turbine is 40 kg/s. The specific enthalpy and velocity in the…

Q: A steam turbine receives a steam flow of 1.25 kg/s and delivers 375 KW. The heat loss from the…

A: Given: Mass flow rate is 1.25 kg/s. The power output is 375 kW. The heat loss from the turbine is…

Q: In a gas turbine , the flow rate of air is 4 kg/sec . The velocity and enthalpy of air at the…

Q: Refrigerant-134a enters an adiabatic compressor at 15 psia and 20°F with a volume flow rate of 10…

A: The initial pressure of the refrigerant is P1=15 psia. The initial temperature of the refrigerant is…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: The boundary work of the entire cycle (W). Internal energy change (AU) during the polytropic…

Q: A pump delivers 50 liters/sec of water. The intake to the pump is 75m below the final discharge. The…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: mass flow rate of the air (lbm/s).

A: Given data as per the question For a compressor work-done = 10hp =-5500 lbf ft/s (-ve sign represent…

Q: 2. Areciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079…

Q: Engr. Darmis is tasked to design a frictionless and constant temperature steady-flow system that…

Q: 5 kg/sec of steam enters the condenser at 0.10 mpa and 88% quality. The cooling water enters @ 33C…

A: Given, Steam: P1=0.1 MPa x1=0.88 ms˙=5 kg/s Cooling water: Tin=330CTout=390C Note: 1 m3=1000 L1…

Q: 1. A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the…

Q: 2. An air-conditioning system requires air flow at the main supply duct at a rate of 180 m³/min. The…

Q: 12 kg of air per minute is delivered by a centrifugal air compressor It enters the compressor at a…

Q: The mass flow rate of compressed liquid water through a pump is 20 kg/s and the pressure is…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: Air flows steadily at the rate of 0.5 kg/s through an compressor, entering at 7 m/s speed, 100 kPa…

Q: Ammonia steadily flows at 2.64 lbm/s into an adiabatic compressor as a saturated vapor at 30 F and…

A: Given Data, m˙= Mass flow rate of ammonia = 2.64 lbm/s Inlet condition of ammonia into the…

Q: Q5: A-Steam enters a turbine with a velocity of 35 m/s and specific enthalpy 2990 kJ/kg. the steam…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: A steam power plant of 40% thermal efficiency receives heat of 150 MJ at high temperature while…

A: given data:- efficiency = 40 % heat supplied = 150 MJ work supplied to pump = 10 MJ find , a) heat…

Q: 12 kg of air per minute is delivered by a centrifugal air compressor It enters the compressor at a…

Q: Define the energy equation of a uniformflow system reduces to that of a closed system when all the…

A: The general expression of the steady flow energy equation can be expressed as,…

Q: A garden hose attached with a nozzle is used to fill a 22-gal bucket. The inner diameter of the hose…

Q: Air enters a gas turbine systenm with a velocity of 105 m/s and has a specific volume of 0.8m/kg.…

A: Air inlet velocity, V1=105 m/s Specific volume of air at inlet, v1=0.8 m3/kg Inlet area of gas…

Q: . The mass flow rate of the gas in a gas turbine is 40 kg/s. The specific enthalpy and velocity in…

A: Given Data Mass flow rate of the gas, m=40 Kg/s h1=1300 KJ/kg v1=160 m/s h2=350 Kj/Kg v2=50 m/s…

Q: steam power plant of 40% thermal efficiency receives heat of 150 MJ at high temperature while…

A: Given data :- thermal efficiency = 40 % heat received = 150 MJ work for circulating water = 10 MJ…

Q: Q5: A-Steam enters a turbine with a velocity of 47 m/s and specific enthalpy 2690 kJ/kg. the steam…

Q: discharges it at 500 kPa through a 100 mm-diameter outlet at 100 m/s. Determine the minimum power…

Q: Air enters the compressor of a gas-turbine engine at 300 K and 100 kPa, where it is compressed to…

Q: A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 ft/cu.…

A: Given data as per question v=500 ft3minp1=15 psiap2=80 psiaρ1=0.079 lbft3ρ2=0.304 lbft3Q=13…

Q: The shaft of a turbine rotates at a speed of 600 rpm. If the torque of the shaft is 3500 N·m, the…

A: Given N=600 rpm T=3500 N.m Asked Power=P=? Formula P=2πNT60

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Question

A water pump increases the water pressure from 15 psia to 80 psia.

a. Determine the flow work, in Btu/lbm, required by the pump. Assume that
the state of the water at pump inlet is saturated liquid and that the specific
volume remains constant during this process.

b. Water enters this pump through a 1.5-in-diameter opening and exits
through a 2-in-diameter opening. Determine the velocity of the water at the
inlet and outlet when the mass flow rate through the pump is 1.1 lbm/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pump with an overall efficiency of 60% is pumping an acid (p= 1800kg/m3) from an open tank (atmospheric pressure) to a reactor unit at the rate of (8 square root 8) kg/s. This unit operates at 8000 Pa gauge and the acid is discharged into it with a velocity of 0.24 m/s at a point 6m above the acid surface level in the tank. Determine the power required (kW) to run the pump if the sum of the major and minor energy losses are equivalent to 3m of H2O head.
1. Steam flows into a turbine at the rate of 10 kg/s and 10 kW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from turbine.
A simple saturated refrigeration R-12 system operates at an evaporating temperature of -11 °C and a condensing temperature of 40 °C. Determine the volume flow in m3/sec rate for a refrigerant capacity of 1 kW.
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP? draw a diagram and show full solution
A centrifugal air compressor handles 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 cu ft/ lb and the final specific volume is 3.25 cu ft/lb. If the inlet suction line is 4-in ID and the discharge line is 2.5-in ID, determine (a) the change in flow energy between the boundaries, ft-lb/min, (b) the mass rate of flow, lb/min, and the (c) change in velocity. (draw a diagram)
An air compressor has a suction volume of 0.35 cubic meter/sec at 28 deg. C and 101.325 Kpa and discharges 700 kpa. Determine the amount of power saved by the compressor in two staging?
A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 ft3/lb and the final specific volume is 3.25 ft3/lb. If the inlet suction line is 4 in. ID and the discharge line is 2.5 in. ID, determine (a) the change in flow work between the boundaries, ft-lb/min; (b) the mass rate of flow, lb/min; and (c) the change in velocity. Answer: (a) 324,000, (b) 15.88, (c) -12.9 fps
The mass flow rate of the gas in a gas turbine is 40 kg/s. The specific enthalpy and velocity in the inlet are 1300 kJ/kg and 160 m/s respectively while the outlet are 350 kJ/kg and 50 m/s respectively. Calculate for the work of the turbine if there is a heat loss of 1000 kW. (kW)
Water with a specific heat of 1 BTU/lbmoF is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 400 BTU/min of heat is lost from the system. What is the temperature (oF) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35oF).
A pump delivers 50 liters/sec of water. The intake to the pump is 75m below the final discharge. The inlet and discharge pressure is essentially atmospheric and the temperature of the water remains constant at 20 ⁰C during the process. Determine the power required by the Pump.
1. A deaerator heater supplies 150 L/min of deaerated feedwater into a booster pump at 115 oC pumping temperature. The heater pressure is maintained at 100 kPag by bleed steam. Pump centerline is located 1 m above the floor level. Suction line losses is 0.60 m. Determine the minimum height of water level in the heater that must be maintained above the centerline of the pump to avoid cavitation, if the pump to be installed has a required suction head of 5.8 m.
Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 150W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions.Calculate the total rate of entropy production in