() A wastewater sample is being analyzed to determine its BOD content. The sample is diluted in order to perform the test 295 ml, of distilled water are added to 5 ml of sample to fill the 300 ml BOD bottle. The bottle has an initial dissolved oxygen concentration of7.9 mg/L After incubating 5 days, the dissolved oxygen concentration is 45 mg/L a. What is the S-day BOD of the wastewater? h. The deoxygenation rate constant, k. is 0.013 day What is the ultin BOD of the wastewater?

() A wastewater sample is being analyzed to determine its BOD content. The sample is diluted in order to perform the test 295 ml, of distilled water are added to 5 ml of sample to fill the 300 ml BOD bottle. The bottle has an initial dissolved oxygen concentration of7.9 mg/L After incubating 5 days, the dissolved oxygen concentration is 45 mg/L a. What is the S-day BOD of the wastewater? h. The deoxygenation rate constant, k. is 0.013 day What is the ultin BOD of the wastewater?

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

In standardization, 10.00 mL of Naz C2 04 solution required 39.17 mL of KMN04. Find the molarity of KMNO,. The unknown required 14.44 mL of MnO,. Find Ca in the urine. (Answer: 1.086 x 10 M, 7.840 x 10 M)
Determine the pH of a solution that contains 2*(10^-4) mg/L of OH- (at 25 degrees).
The Volume of NaOH (0.01N) when use ph.ph indicator is 12.4mL and 3mL when use methyl Orange (M.O) and the Volume of Sample is 30mL, Calculate the Total Acidity as mg (CaCO3)/L. (EW for CaCO3 is 50)
The pOH of a basic solution is 3.33. What is pH?
Chose the correct answer 1- The Unit measurement of suspended solids is ...A- kg 2- The Unit measurement of Turbidity is A- °C is B-m B-NTU C- mg/L C-K 3- The Unit measurement of pH www A-mg/L 4- The Unit measurement of alkalinity is .. 5-Non toxic metals includes 6-Dissolved materials size is lees than A- 10 mm D- none of above D- none of above D- none of above B- p.p.m C- g/m³ D- none of above A- m/sec B- m³/sec C- mg/L A-Chromium B- Mercury C- Calcium D- none of above B- 106, C-108 mm D- none of above mm 7- Public standards of Hardness in drinking water is A-500 mg/L B-50 mg/L C-100 mg/L D- none of above 8- Alkalinity species includes are A-HCO3 B-CO3 C- OH D-All of above ... 9- Dental cavities in children can prevented when Drinking water has Fluoride concentration of A- 0.1 mg/L B- 1 mg/L C- 10 mg/L D- none of above 10- Toxic metals are metals that harmful to humans even when exists in concentration of .. A- Small B-Large C-zero D- none of above
3. Table below shows the concentration of dissolve oxygen for a BOD test, diluted by 100. Time (days) Diluted sample DO (mg/L) 7.95 1 3.75 2 3.45 2.75 2.15 1.8 i. Determine BOD5 Given the deoxygenation rate coefficient of 0.15 day-1, determine the ultimate BOD ii. iii. Based on answer from (i), identify class of the water sample based on INWQS guideline and propose suitable usage the water.
(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate (SO2-) Carbonate (CO2) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.
6 Ydu will obtain 2.0 L of tap water for you water hardness test. The water hardness test uses a precipitation reaction to precipitate the Calcium bicarbonate present out of solution by adding 1.9 g of Ca(OH) represented by the following equation: Ca(HC03|21ag) + Ca(OH)215) > 2CaCOsisi + 2 H20 ml What is the percent yield of CaCO3 produced in the hard water test? (fig. 4)
Il Consider the capability of a process that puts pressurized grease in an aerosol can. The design specification calls for an average of 50 pounds per square inch (psi) of pressure in each can with an upper tolerance limit of 56psi and a lower tolerance limit of 46psi. A sample is taken from production, and it is found that the cans average 51psi with a standard deviation of 2psi. Find the following unknowns. 1. Capability Index (Cpk) 2. Is the process capable at the 30 level? 3. What is the probability of producing a defect? Hind: use the standard normal table as seen below.
The following test results (Table Ql-2) were obtained from a raw water sample. All of the tests were performed using a sample volume of 50 mL. Table Q1-2 Weight (g) Mass of residue after drying at 105 ỏC Mass of residue after ignition at 550 ¿C Mass of residue on Whatman GF/C filter paper after drying at 0.7148 0.3818 0.3571 105 'C Mass of residue on Whatman GF/C filter paper after ignition at 550 'C 0.1418 Calculate the concentration (mg/L) of : (i) total solids. (ii) total volatile solids. (iii) total suspended solids. (iv) total dissolved solids.
9. A core sample is saturated with Oil, Gas and Water , the initial weight of the saturated sample is 220 gm . After the gas is displaced by water , the weight is increased to 222gm. the sample is then placed in soxhlet distillation apparatus , only 5cc of water was extracted .After cleaning and drying the core , the weight was 210 gm .the sample bulk volume is 100 cc , Pw = 1 gm /cc . Po =0.85 gm/cc .Calculate the effective porosity , Absolute porosity, the saturation of Oil, water and gas .
A sample of water was analyzed through titration with 0.01N HCI. 150 mL of the water required 30.0 ml of 0.01 N HCI to titrate it to the phenolphthalein endpoint and 14.0 mL of the same HCI solution to titrate it further to the methyl orange endpoint. Assuming the sample contains no calcite particles, what are the total and carbonate alkalinities of the sample in meq/liter and the total alkalinity in mg/liter as CaCo,? Also, what are the concentrations of the major alkalinity species?