A W 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm² d = 549 mm I, = 862 x105 mm² l, = 38.7 x105 mm* tw = 14.7 mm b, = 214 mm t₁ = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75kN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015

A W 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm² d = 549 mm I, = 862 x105 mm² l, = 38.7 x105 mm* tw = 14.7 mm b, = 214 mm t₁ = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75kN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d=312 mm bf - 102 mm tf 10.8 mm tw = 6.60 mm kdes 18.4 mm ry-21.5 mm Ix- 64.5 x 10^6 mm^4 ly- 1.94 x 10^6 mm^4 Sx416 x 10^3 mm^3 Zx 480 x 10^3 mm^3 J-122 x 10^3 mm^3 Cw-44.0 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 89 KN-m O 114 KN-m O 123 KN-m O 101 KN-m
Situation 1: A W8x31 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d=203 mm bf = 203 mm tf-11.0 mm tw = 7.24 mm kdes - 21.1 mm ry = 51.3 mm Ix = 45.8 x 10^6 mm^4 ly- 15.4 x 10^6 mm^4 Sx-451 x 10^3 mm^3 Zx = 498 x 10^3 mm^3 J-223 x 10^3 mm^3 Cw-142 x 10^9 mm^6 1. Which of the following nearly gives the maximum safe uniform load (Wu) that the beam could carry if the span of the beam is 5m? Neglect weight of the beam. 46 KN/m 41 KN/m 51 KN/m 33 KN/m
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
AW 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm? , = 862 x10 mm d = 549 mm 4 = 38.7 x10 mm tw = 14.7 mm bị = 214 mm t, = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75KN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015
A W420x85 steel beam is fully restrained with a uniformly distributed live load of 25 kN/m. The beam has a span of 10m. Use A36 steel. Properties of W40 x 85 A = 10839 mm2 %D bf = 180 mm tf = 18 mm %3D tw = = 11 mm Ix = 310 x 106 mm4 %3D d = 420 mm (Note: Since this is a built-up section, for checking of web slenderness, use h = d - 2t;) %3D 1) Calculate the design shear strength of the section. Check if the section is adequate in shear. USE LRFD and U = 1.2D + 1.6L. %3D 2) Is the maximum deflection at the midspan of the beam due to live load adequate? 3) Calculate the maximum uniform live load that can be carried by the beam.
Determine the maximum safe service live load that the beam can carry if the service dead load is 10kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPA and fy=415MPa. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70 mm 300 mm 7.2m 6.7m A В O O
A W14x68 is used as a beam having a simple span of 6m. Properties of WF section. d=356.62mm bf=254.89mm tf=18.29mm tw=10.54mm Sx=1688x10^3mm3 Ry=62.48mm Zx=1885x10^3 mm3 Fy=345.6 Mpa EI=150000 Kn-m^2 Compute the safe uniform load (Wa) it could support due to the shear strength of the beam. Use Case 1 for hit rolled shape conditions using ASD method l. (kN/m)
A beam carries a concentrated load W and a total uniformly distributed load of 4W as shown in Fig. . What safe value of W can be applied if fbc ≤ 100 MPa and fbt ≤ 60 MPa? Can a greater load be applied if the section is inverted? Explain. W La T N.A. |k-₂m-k R₁ INA = 24 x 105 mm* 4W 4m R₂ 75 mm 125 mm
Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d-312 mm bf - 102 mm tf = 10.8 mm tw = 6.60 mm kdes - 18.4 mm ry-21.5 mm Ix - 64.5 x 10^6 mm^4 ly-1.94 x 10^6 mm^4 Sx - 416 x 10^3 mm^3 Zx 480 x 10^3 mm^3 J-122 x 10^3 mm^3 Cw-44.0 x 10^9 mm^6 1. Which of the following nearly gives the maximum safe uniform load (Wu) that the beam could if the span of the beam is 0.800m? Neglect weight of the beam. 960 KN/m 933 KN/m 922 KN/m 975 KN/m
The given girder has beams framing into it at the ends and at every L/3 point. The beam carries a service live load of 20 kips as shown and superimposed uniformly distributed service dead load of 10 kip/ft. Select the lightest A992 W-section that can carry the load. Do not check for deflection. P, = 20 kips LL PLL W. = 10 kip/ft DL = 20 ft WDL L/3 BEAMS FRAMING INTO GIRDER L
Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d - 328 mm bf-310 mm tf = 25.1 mm tw = 15.5 mm kdes - 40.4 mm ry - 79.0 mm lx = 388 x 10^6 mm^4 ly - 125 x 10^6 mm^4 Sx - 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 878 KN-m 793 KN-m 836 KN-m 811 KN m
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.