A vertical square prism of 40 mm base side is completely penetrated by horizontal square prism of base 25 mm side. Axis of horizontal prism is parallel to both the reference planes and bisects the axis of the vertical solid. All the faces of vertical square prism are equally inclined to the V.P. One of the faces of horizontal solid is inclined at an angle 300 to the H.P. Draw the orthographic projections showing the lines of intersections. Assume suitable lengths of both the solids.

A vertical square prism of 40 mm base side is completely penetrated by horizontal square prism of base 25 mm side. Axis of horizontal prism is parallel to both the reference planes and bisects the axis of the vertical solid. All the faces of vertical square prism are equally inclined to the V.P. One of the faces of horizontal solid is inclined at an angle 300 to the H.P. Draw the orthographic projections showing the lines of intersections. Assume suitable lengths of both the solids.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

Draw isometric projection of a cylinder of diameter 30 mm and height 50 mm
A rectangular block measures 100 mm by 80 mm by 60 mm. Draw a section view of the block with a section line inclined at 45 degrees to the horizontal plane.
A line RS of 55 mm in length is inclined to HP by 30o and parallel to VP. One of its end points is above HP by 20 mm and in front of VP by 30 mm. The line is in single quadrant. Find the projections of the line RS and find out its horizontal trace.
An equilateral triangle of 35 mm side has an edge in the HP which is inclined at 40° to the VP. The plane itself is inclined at 50° to the HP. Draw the projections of this plane.
4. A cube of side 35 mm is kept on HP with base edges equally inclined to VP. It is cut by a plane perpendicular to VP and inclined to HP in such a way that the true shape of the section is a regular hexagon of maximum size. Draw the front view, top view, and true shape of section. Also determine the inclination of the cutting plane with HP. Hint After keeping the cube in desired position, Draw sectional top view such that the distances 1-6 and 3-4 are haif the distance 2-5. 1,3,4,& 6 are mid points of edges (because in a hexagon, distance across corners is twice the length of edge of hexagon) 5 Hint for Q3 Hint for Q4
Construct a rhombus having diagonals of length 60 mm and 75 mm and measure the length of a side.
View Image. Show complete and detailed solution. Please write legibly. Answer: 64.3 degrees
Q1/3-The B Rep. Scheme for the box consists of: * O 8 faces, 8 edges & 12 vertices O 6 faces, 8 edges & 12 vertices 8 faces, 12 edges & 12 vertices O 6 faces, 12 edges & 8 vertices
Draw an isometric view of hexagonal prism of side 40 mm and height 60 mm.
Find the centroid of the plate shown in figure. Where B = 95 mm, b= 18 mm, d =54 mm, y = 15mm (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) B (i) The Area of full Triangle (unit in mm2) is =,
Please find the miller indicies for the plane picture below. This cube is equal on all sides and all angles are 90 degrees. Indicate where you move the origin if required.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.