A V-belt pulley is made of cast iron with 240 mm. in diameter is connected to a 360 mm. diameter driven pulley on the parallel shaft that runs on the same direction. The center distance between the pulleys is 520 mm. Determine the following: The length of arc for angle 8 in mm (Example for the answer: 388. 62)

A V-belt pulley is made of cast iron with 240 mm. in diameter is connected to a 360 mm. diameter driven pulley on the parallel shaft that runs on the same direction. The center distance between the pulleys is 520 mm. Determine the following: The length of arc for angle 8 in mm (Example for the answer: 388. 62)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in. and 18 in., respectively.
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
solve show all ateps and solutiion
solve using laplace
Please solve part b : 1,2,3
IS. 03 16. The shaft, as shown in Fig. 14.20, is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 3.5. B. TA2 A D. TA 150 -100- TB2 100 All dimensions in mm. Fig. 14.20 The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile stress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion and bending factors as 1.25 and 1.75 respectively, find the shaft diameter. Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare the weights of the two shafts. Ans. 30 mm : 24 mm: 1.82]
Given: L1 = 7.25 in., L2 = 2.00 in., L3 = 7.00 in., L4 = 4.50 in., 01 = 5°, and 0, = 150°. Analytically determine the angular position of links 3 and 4 assuming Figure 2.32 is drawn roughly to scale. (Answers: 03 = 27.3°, 04 = 127.4°). D L3 L4 Loc Bo 02 L2 Ao
The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable Shearing Stress:85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
I will be selling a Summer Camp Innovative Sleeping System (SCISS) that suspends beds from the ceiling to make cleaning the floor easier (and to avoid snakes, bugs, and rodents). The top post is a 4-foot long steel post with a 2.5 inch x 2.5 inch cross section. The bottom post is a 3-foot long aluminum post with a 2 inch x 2 inch cross section. (a) What is the displacement of point “C" for the loading shown? (b) Has the yield stress of either post been exceeded? (c) What is the displacement of point “C” if the 120 lb loads are put on the top beds, and the 180 lb loads are put on the bottom beds? (d) For the loading in part (c), has the yield stress of either post been exceeded? 180 lb 120 lb -A- Steel Aluminum O 180 lb 120 lb
What is the over-turning moment at x = 0, of a hollow tube that has an OD of 40 mm, and an ID of 20 mm. The length of the tube is 960 mm. It is attached to a 1 inch thick plate.
A driving sprocket with 12 teeth drives another sprocket with 48 teeth by means of a chain having a pitch of 3/4-in. If chain length is 75-in, find the center distance between sprockets. (Ans. 25.89 in)