A two diode full wave rectifier connected to a 230 V/(10-0-10)V centre tapped transformer supplies to a load resistance of 10kn. Assuming resistance of half of the secondary winding as 10 and forward resistance of diode as 20 Q, calculate peak value of load current Average value of Load current RMS value of Load current Rectifier efficiency Dripple voltage and Peak Inverse Voltage

A two diode full wave rectifier connected to a 230 V/(10-0-10)V centre tapped transformer supplies to a load resistance of 10kn. Assuming resistance of half of the secondary winding as 10 and forward resistance of diode as 20 Q, calculate peak value of load current Average value of Load current RMS value of Load current Rectifier efficiency Dripple voltage and Peak Inverse Voltage

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
QUESTION 2.. A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7K OHM d) Find the effective value of the load voltage.e) Find the effective value of the load current.
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the peak signal voltage received by the diode
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
Why is the ripple voltage inversely proportional to the Load Resistance and Capacitance in an rectifier circuit.
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
Full Wave Rectifier Circuit The circuit of the full-wave rectifier can be constructed in two ways. The first method uses a centre tapped transformer and two diodes. This arrangement is known as a centre tapped full-wave rectifier. The second method uses a standard transformer with four diodes arranged as a bridge. This is known as a bridge rectifier. Advantages of Full Wave Rectifier The rectification efficiency of full wave rectifiers is double that of half wave rectifiers. The efficiency of half wave rectifiers is 40.6% while the rectification efficiency of full wave rectifiers is 81.2%. The ripple factor in full wave rectifiers is low hence a simple filter is required. The value of ripple factor in full wave rectifier is 0.482 while in half wave rectifier it is about 1.21. The output voltage and the output power obtained in full wave rectifiers are higher than that obtained using half wave rectifiers. Question: What is the main disadvantage of a conventional full-wave…
In a centre-tapped full wave rectifier, the diode having a forward resistance of 3 ohm and the load resistance equals to 750 ohm. The turns ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS) 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency.