A transmission tower shown below is subjected to lateral loads as shown. A =2.3 kN, B =5.7 kN, C =6.8 kN Determine the magnitude of the axial force in member EG (in kN). Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m

A transmission tower shown below is subjected to lateral loads as shown. A =2.3 kN, B =5.7 kN, C =6.8 kN Determine the magnitude of the axial force in member EG (in kN). Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Replace the loading on the frame by a single resultant force. Suppose that F₁ = 450 N F₂ = 650 N, F3 = 950 N, and F₁ = 600 N. (Figure 1) igure F₁ 0.5 m F₂A -1 m- 1.5 m 1m B T0.5 m x 1 of 1 ▼ Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 = Submit Part C O x = μA Value Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. VE ΑΣΦ || Ivec Request Answer Request Answer Units μA Value ? Specify where the line of action of the resultant force intersects a horizontal line along member CB, measured from end C. Express your answer to three significant figures and include the appropriate units. Enter positive value if the line of action intersects a horizontal line CB to the right from end C and negative value if the line of action intersects a horizontal line CB to the left from end C. Units ? ? °, measured clockwise from the positive x axis
PROBLEM SET Situation 1 The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50 KN. Compute the vertical movement under the load. Aluminum E«70 GPa Steel L-4m E-200 GPa A=500 mm? L-3m A-300 mm 2 m
An elliptical gate covers the end of a pipe 4m in diameter. Of the gate is hinged at the top, what normal force F is required to open the gate when water is 8m deep above the top of pipe and the pipe is open to the atmosphere on the other side? Neglect the weight of the gate. Find: ħ in kPa Agate in m2 FR in kN ȳ in m I in m4 ycp in m F in kN
The shaft is made of A-36 steel. It has a diameter of 28 mm and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa (Figure 1) Part A Determine the angle of twist of gear C with respect to B Express your answer using three significant figures. vec ? OC/B = rad Submit Request Answer Figure < 1 of 1 Provide Feedback В 90 N-m 0.6 m 90 N.m 0.75 m 0.9 m
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. E=200 GPa A=D300mm? L=3m 2m 2 m 3m 1.5m Match each tem to a choice
The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and is loaded by two torques. Use Goronze = 35 GPa, Galum. = 28 GPa, and Gsteel = 83 GPa. Bronze Aluminum Steel diameter 25 mm diameter 50 mm diameter = 25 mm Te =300 N.m K To =700 N.m
Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm
QUESTION 1 The following beam is simply supported, the support at A is a pin and B is a roller. The concentrated load of 40 N is located in the center of the beam. What are the boundary conditions you would use to determine the equation of the elastic curve for the beam using the x coordinate that is valid for 0 sxSL? Provide the values you would us in the equations. 40 N IT Arial 3 (12pt) 三 ABC i nd Submit to save and submit. Click Save All Answers to save all answers.
The resultant couple of the three couples acting on the triangular block is to be zero. Suppose that R = 190 N . (Figure 1) Determine the magnitude of force F. Express your answer to three significant figures and include the appropriate units. ? µA F = Value Units Submit Request Answer Figure < 1 of 1 Part B Determine the magnitude of force P. Express your answer to three significant figures and include the appropriate units. -F ? HA R P = Value Units 300 mm 500 mm 600 mm -R Submit Request Answer 400 mm
The rigid AB beam shown in the figure is supported by elastic rods 1 and 2 at points A and B. Calculate the stresses that will occur in bars 1 and 2. (E-200 GPa and A=5 cm^2) E 464 4m 3 kN/m 6m Doo 10 EA 1 77777 D | rijit 5m 7m 2EA B₁
The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P = 50 kN, determine its vertical movement. STEEL L=3 M A= 300 mm² E= 200 GPa 2m зм P= 50 KN ALUMINUM L=43 A== 1500 mm² E-7067.
Fig.( a) shows a steel wire 1 mm diameter is stretched horizontally between two fixed points apart. A vertical load applied at the mid span of the wire causes a vertical displacement of 45 of the point of application of the load applied. What will be the stress induced in the wire and load applied? Neglect the weight of the wire. Take E for the wire material as 200 GN/m². F L 1 m P S N -1 m- M