A thin-walled cylindrical pressure vessel of inner radius r is subjected simultaneously to internal gas pressure p and a compressive force F acting at the ends. (See the figure. Assume the internal pressure is gage pressure.) Ⓡ (a) What should be the magnitude of the force F in order to produce pure shear in the wall of the cylinder? (Use the following as necessary: p, r, and t for the wall thickness.) F= (b) If force F = 190 kN, internal pressure p = 9 MPa, inner diameter = 200 mm, and allowable normal and shear stresses are 144 MPa and 72 MPa, respectively, what is the required thickness of the vessel (in mm)? mm

A thin-walled cylindrical pressure vessel of inner radius r is subjected simultaneously to internal gas pressure p and a compressive force F acting at the ends. (See the figure. Assume the internal pressure is gage pressure.) Ⓡ (a) What should be the magnitude of the force F in order to produce pure shear in the wall of the cylinder? (Use the following as necessary: p, r, and t for the wall thickness.) F= (b) If force F = 190 kN, internal pressure p = 9 MPa, inner diameter = 200 mm, and allowable normal and shear stresses are 144 MPa and 72 MPa, respectively, what is the required thickness of the vessel (in mm)? mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. B. 300 mm E P=36 kN 300 mm 400 mm 500 mm
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. L. C D VAR 2m +12m -1.2 m-1.2 m 1.2 m-
As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm and an inner diameter of 24 mm. 50 N force at an angle of 30 ° with the y-axis at the free end C to the ABC rod is implemented. (a)Show and calculate the cross-sectional effects on the cross-section a a. (b) Calculate the stresses occurring at the H point of the ABC bar and calculate these stresses
Topic: Thin Walled Tubes The constant wall thickness of a steel tube with the cross section shown is2 mm. If a 600-N m torque is applied to the tube, find (a) the shear stress in the wallof the tube; and (b) the angle of twist per meter of length. Use G= 80 GPa for steel.
Calculate the shear stress on a-a plane.
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P-100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Sectian 300 800 ISM P= 300 kl, e = 250mm From the given figure shown, Calculate the stress at the top located in the centerline of the beam. (MPa)
The constant wall thickness of a steel tube with the cross section shown is2 mm. If a 600-N m torque is applied to the tube, find (a) the shear stress in the wallof the tube; and (b) the angle of twist per meter of length. Use G= 80 GPa for steel.