a) The power supplied to a three-phase induction motor is 32kW and the stator losses are 1200W. If the slip is 5% , determine i. The rotor copper loss. ii. The total mechanical power developed by the rotor iii. The output power of the motor if friction and windage losses are 750W iv. The efficiency of the motor, neglecting rotor iron loss

a) The power supplied to a three-phase induction motor is 32kW and the stator losses are 1200W. If the slip is 5% , determine i. The rotor copper loss. ii. The total mechanical power developed by the rotor iii. The output power of the motor if friction and windage losses are 750W iv. The efficiency of the motor, neglecting rotor iron loss

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
7- Iron loss in the rotor of a 3-phase induction motor is negligible due to (a) Very low frequency of emf induced in the rotor (c) Very low flux density in rotor parts 8- The starting current of a 3-phase induction motor is about (a) Half (c) 5 to 7 times (b) Twice (d) 8 to 10 times 9- During plugging of an induction motor (a) Phase sequence is reversed (b) A de source is connected to stator (e) One phase is open circaited (d) Power is ied back to mains 10- Direct online (D.O.L.) starter is used for induction motors (a)Less than 5 h.p. (b) Less than 10 h.p. (c) Greater than 10 h.p. (d) For any capacity (b) Very low emf induced in the rotor (d) Constant magnitude of flux linking the rotor core of its full load rated current
a) The rotor power output of a 3-phase induction motor is 15 kW and the corresponding slip is 4%. The rotor copper loss will be..
1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
Discuss the following statements briefly 1. Adding auxiliary winding in single phase induction motors. The starting capacitor of a capacitor start capacitor run induction motor is 100 µF while the running capacitor is 14 µF.
The name plate of single phase induction motor has following data output 373W,230V, frequency 50Hz. Input current 2.9A and power factor is 0.71. Speed 1420 rpm What is efficiency of motor.
T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
What are the following statements are true for a three-phase induction motor? I. Three-phase induction motor stator winding is fed from a single-phase supply II. Stator carries a three-phase winding III. Rotor carries a short circuited winding a. I,II and III b. I only c. I and II only d. II and III
What will be the operating power factor of a 3-phase induction motor, whose ratings are 230 V, 50 Hz, 120 hp, and 4-poles? Motor is operating at rated conditions with an efficiency of 92% and draws a line current of 260 A. The core loss and stator copper losses are 1710 W and 2830 W respectively. (a) 0.85 (c) 0.93 (b) 0.90 (d) 0.80
The rotor of a 3-phase, 60 Hz, 4-pole induction motor takes 118 kW at 3Hz. The motor has stator copped loss of 2.95 kW, a mechanical loss of 2kW and a stator core loss of 1.7 kW. Solve for the motor efficiency