A substation transformer is serving the following loads: Classification Total Load Demand Factor Lighting 300 kW 60% Power 1200 kW 80% Heating 500 kW 90% If the diversity factor among the load types is 1.5, determine the demand factor of the transformer. Subject: DISTRIBUTION SYSTEM

A substation transformer is serving the following loads: Classification Total Load Demand Factor Lighting 300 kW 60% Power 1200 kW 80% Heating 500 kW 90% If the diversity factor among the load types is 1.5, determine the demand factor of the transformer. Subject: DISTRIBUTION SYSTEM

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.63P: A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a...

See similar textbooks

Related questions

Q: RT, IT, 11, I 2, 1 3, I 4, I 5, 16 I3 R1= 3kN R3= 2k2 I Rs= 5kN I6 111V R2= 8kN R= 7k2 R= 6k2

Q: Consider a silicon pn junction at T = 300 K. Assume the doping concentration in the n region is 1020...

A: We need to find out the minorities carrier density for given diode .

Q: An autotransformer having a transformation ratio of 0.62 supplies a load of 2 kW. The power transfer...

Q: What is a rectifier circuit? Give at least 3 applications of rectifier circuit.

Q: Solve completely the given circuit below by applying two ac theorems discussed. Choose among Kirchho...

Q: what us the resistance of teb 240- resistors connected in series? in parallel?

Q: DETERMINE THE OUTRUT VOLJAGE (VO) OF A DIFFERENTIAL AMPURER FOR THE INPUT VOLTAGES f 300 miorovolt a...

Q: 1.Calculate by the method of your choice the voltage, current and power in R4 of the circuit 2. Find...

Q: A 20-kVA, 507 V load is to be supplied by an ideal step-up autotransformer from a 400-V source. Find...

A: Neglecting the losses in transformer input power KVA = output KVA. VA=voltage×current.

Q: Convert 1000 W into its equivalent mechanical horsepower.

A: In this case, 1000 W of power is to be converted into its equivalent power in mechanical horsepower....

Q: Given the one-line diagram; a duplex switch controls each lamp A and B, individually. , and a lamp C...

A: The one-line diagram is shown below,

Q: Question # 2: A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and seco...

Q: Voltage is the energy required to move a unit charge through an element, measured in volts (V). * Ye...

A: Given, Voltage is the energy required to move a unit charge through an element, measured in volts? ...

Q: The time period of a sine wave is 0.05 seconds. The frequency of the sine wave is О а. 20 Нz O b. 40...

A: Given, Time period of sine wave is, T = 0.05 sec

Q: power station can generate only small power. A2 a) Diesel b) Hydro Electric c) Nuclear d) Thermal

A: The solution is given below

Q: on junction at its limits

A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is revers...

Q: R3 A F E 1 E R1 В R2 E2. D Otheexpertta.com

Q: Given the following wye-connected resistances: Ra = 11 Ω, Rb = 4 Ω, and Rc = 11 Ω, calculate the val...

Q: Load Balance Diagram (Questions 7-10) 24- 22 - 20 Tc 18 - 16 - 14 - 12 - Task Duration (min's) A 10 ...

A: Given data Duration of A is Ta=10min Duration of B is Tb=8min Duration of C is Tc=3min Duration of D...

Q: (а) Figure Q1(a) shows an amplifier with negative feedback. Explain how does the inclusion of the ne...

Q: Determine the current l2 in the circuit below in polar form. Write the magnitude only in four decima...

Q: Q2/ In an air-filled rectangular waveguide, the cutoff frequency of a TE10 mode is 5 GHz, whereas th...

Q: Find the transfer function Vo(s)/V(s) of the circuit. *

A: Convert the given circuit into s domain and apply kirchhoff's current law into negative terminal of ...

Q: Give example problems for admittance. Formula: Y = G ± jB = 1/Z.

A: Admittance problem

Q: What is the mass of an electron?

A: Mass of an electron.

Q: Calculate the time constant for an RC circuit with the following values: What are the Values of the...

A: Given (a): R = 1KΩ, C = 100nF (b): R = 10KΩ, C = 100nF

Q: Three impedances Z1, Z2 and ZL are connected in tee. The impedance Z1 is connected in series with th...

Q: R1 300 N L1 500 mH vi(t) 20 μF R2 500 N ww L2 600 mH ww

Q: 8. Calculate effective density of states for holes in Ge at temperature 70°C. 9. Calculate the conce...

A: Effective density of states directly proportional to (T)^1.5 Intrinsic concentration is [square root...

Q: 3V2 - 42 1 H 0000 2 H F0000 F 4/2 cos(vZt) [*Revised Image] By what phase does the current through t...

Q: Find the equivalent inductance of the circuit if L= 20H 25 H 20 H 20 H 60 H. 10 H 30H

A: In this question we will find equivalent inductance of circuit....

Q: 4+j30 3+j60 j3n N) 10020°V 3-j6N 50 5+j80

Q: Consider a silicon pn junction at T 300K. Assume the doping concentration in the n region is 1020cm ...

Q: Given the circuit below, Calculate the following: 15 V A 1 KHz a. Voltage drop between Points A and ...

Q: 2. A pair of automotive headlamps is connected to a 12 V battery via the arrangement shown in figure...

A: Given circuit,

Q: I'm trying to study Microcontroller instructions (PIC16F877A) by Assembly (35 instructions), so I ne...

A: Microcontroller-Microcontroller is a form of integrated chip. It a combination of memory, input outp...

Q: 5s^2+ 29s+ 30)/(s^2+ Ex. 516. F(s)= ( f(t)= A*delta(t) + G exp( -H t ) sin( omega t + K ). Determine...

A: The solution is given below

Q: alternator has 6 poles. (a) At what speed must the machine be driven to develop 60 cycles? 25 cycles...

Q: The periodic signal X(t) is shown ih thế föl repeated every 4 seconds. ing figure. It is a rectangul...

A: We need to represent the given waveform and we need to find Fourier transform of given signal

Q: At Input wavefront →t -5 Voltage across the capacitor

Q: By inspection, which parallel element in Fig. 6.5 has the least con- ductance? Determine the total c...

Q: SOLVE FOR S, Q, P, VR, VL, I, and phase angle. draw the phasor diagram 50ohms R 60иН VR V V = 210210...

Q: 1. For the network of Fig, 1, determine: a) Vg=. b) IDa c) VgSq d) Vpsq e) Vp =- ) Vs = 2. For the n...

Q: Fedmeter uction oet heo O r O ver var O vr OA heh

Q: With the help of a circuit diagram show that using germanium diode clipper, how we can achieve an ac...

Q: 12–5. The velocity of a particle traveling in a straight line is given by v = (6t – 3²) m/s, where t...

Q: 2. For the circuit in Figure 7-41, determine the following: (a) the power dissipated in the transist...

Q: d. Determine the minimum value of R1 to ensure that the Zener diode is in the “on" state. Rs 220 2 I...

A: Given

Q: Z^2 = 21 - 20j, What are the possible values of Z in rectangular form? +/- ( 5 + 2j) +/- ( 3 + ...

Q: Identify 3 common simple electrical gadget/device at home and for each device; 1. identify safety pr...

A: Three common simple electrical gadgets/devices at home are: 1. FUSES: When there's too much current ...

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.