A steam bath center in a gym consists of a wall three different material layers. First two layers have thermal conductivity of 5 W/m K, 10 W/m K and 2*(10) W/m K respectively. All three layers have thickness of 8 cm each. The inside wall surface temperature of steam room is 80 °C whereas outside surface temperature is 25 °C. Draw this composite wall. Calculate the heat transfer per unit length of the wall.

A steam bath center in a gym consists of a wall three different material layers. First two layers have thermal conductivity of 5 W/m K, 10 W/m K and 2*(10) W/m K respectively. All three layers have thickness of 8 cm each. The inside wall surface temperature of steam room is 80 °C whereas outside surface temperature is 25 °C. Draw this composite wall. Calculate the heat transfer per unit length of the wall.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.10P: 1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss...

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
A metal furnace with a 1.25 m x 0.75 m metal door is placed in a room and set to 400K. A 0.3 m x 0.3 m glass window is located in the furnace door. The thickness of the metal alloy and the glass window are 3 mm and 2 mm, respectively. The glass window has a thermal conductivity (k) of 0.7 W/m .K and the metal door has a thermal conductivity (k) of 3.5 W/m.K. The convective heat coefficient hi and ho on each site of the furnace door is estimated as 10W/m2.K. Assuming the room temperature is held constant at 297 K, calculate the total heat loss from the furnace door. P.S Could you write the solution clearly to better understanding? Step by step using formulas. Another page with detailed steps would be better. Thanks in advance.
20-m pipe has an outside diameter of 50 mm. Pipe is insulated with a layer of asbestos, then followed by a layer of cork. Inside and outside diameter of the cork is 77 mm and 80 mm, respectively. If the temperature drop from pipe to cork is 1165°C, calculate the inside diameter of the pipe (mm). The rate of the heat transfer is 8778 W. The thermal conductivity of steam pipe, asbestos and cork are 0.045 kW/m-K, 0.058 W/m-K and 0.043 W/m-K respectively.
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
2.The owner of the house in number 1 is thinking that heat of 1.2 kW coming from the wall is too high, he then decides to add a layer of 5 cm of expanded polystyrene in order to insulate the building. The rest of the wall is still be made of bricks. Bricks have a conductivity of 0.8 W/m/K and are 15 cm wide. Expanded polystyrene has a thermal conductivity of 0.04W/m/K The wall is 6 m long per 3 m high. He measures now 35 degrees on the outside surface and 22 degrees on the surface of the wall inside. Calculate the heat transferred.
A wall is made of firebricks 9 inches thick and has a 700F difference in the temperature of both sides. Calculate the heat transferred through the wall if the thermal conductivity of the bricks is 0.65 BTU/hr-ft-0
Calculate the rate of heat loss through the vertical walls of a boiler furnace of size 4 m by 3 m by 3 m high. The walls are constructed from an inner fire brick wall 25 cm thick of thermal conductivity 0.4 W/mK. The inside temperature of the fire brick layer was measured at 600 C and the temperature of the outside was 60 C.
An aluminum tube is 200 cm long and has a outside diameter of 2 cm and wall thickness of 5 mm. One end is kept at a constant temperature of 300°C and the other is kept at a temperature or 10 °C. Assume the tube sides are adiabatic. Calculate the heat transfer through the tube. Use finite difference analysis to calculate the temperature very 10 cms.
A cold-storage room is constructed of an inner layer of 14 mm of pine with thermal conductivity of 0.15 W/m K, and an outer layer of 75 mm of concrete with thermal conductivity of 0.75 W/m K. The wall surface temperature is 258 K inside the cold room and 298 K at the outside surface of the concrete. Calculate the heat loss in W per 1 m2. Please keep one decimal and take positive value for the final answer.