A square bottomed tank measures 25*25*160cmand is positioned with the bottom of the tank 1mabove sea level and at 20degreesC. The tank is90% filled with water and 10% air. A water inletenters the centre of the tank of 10mm diameter,and no other inlet or outlet is open within thetank. A pump drives water at a starting rate of450ml/min at 0 Pa lowering to 350ml/min as thepressure increases to 800 kPa. The pump andtank are connected by a 10mm diameter pipewith k=0.15 for all fittings and tubing. It shouldbe assumed this is the maximum flow andpressure provided by the pump. The pump willstop instantaneously once the pressure reaches800kPa. The relationship between flow andpressure from the pump should be assumedlinear.What will be the volume of compressed airinside the tank and how long will it take to fill?

Name: A square bottomed tank measures 25*25*160cmand is positioned with the
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A square bottomed tank measures 25*25*160cmand is positioned with the bottom of the tank 1mabove sea level and at 20degreesC. The tank is90% filled with water and 10% air. A water inletenters the centre of the tank of 10mm diameter,and no other inle

Given Data Dimension of the tank =25×25×160cm volume percentage of water in the tank=90% Volume…

Engineering

Mechanical Engineering

A square bottomed tank measures 25*25*160 and is positioned with the bottom of the tank above sea level and at 20degreesC. The tank i 90% filled with water and 10% air. A water inle enters the centre of the tank of 10mm diamete

A square bottomed tank measures 2525160 and is positioned with the bottom of the tank above sea level and at 20degreesC. The tank i 90% filled with water and 10% air. A water inle enters the centre of the tank of 10mm diamete

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A farmer has a pump which discharges 100 lpm of water at a head of 10 m. The pump is driven by anelectric motor at speed of 1700 rpm through 4”x 4” pulley-drive combination for the motor and thepump, respectively, what would be the pump output if the motor pulley is changed to six inchesdiameter?
In an external gear pump, if the delivery rate is 30 cm/revolution, the prime mover's speed which is connected to the pump of with 2670 rpm,Determine The pump delivery in terms of litres per minute is
If the compression ratio is 17:1, the piston displacement volume for 10 cm³ piston clearance volume is. Ans. 160 cm³
Water [2] the diameter of a cylindrical water tank is Do and its height is H. The tank is filled with water, which is open to the atmosphere. An orifice of diameter D with smooth entrance (i.e., no losses) is open at the bottom. Develop a relation for the time required for the tank (a) to empty halfway and (b) to empty completely. Tak Des Onfice Hole Water out
Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water. Ignore any changes in Kinetic or potential energy and assume isothermal flow (ie. Internal energy is constant, this is normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump starting with full energy balance and simplifying to solve for the pump head symbolically. Then begin careful of unit, solve for pump head in feet. Given erosion 500 gpm P=62 lbs/ft^3 A- 10.5 ft B- 100.8 ft C- 50.1 ft D-80.7 ft
A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 metres. If the overall efficieney of the pump is 70%, find the power required for the pump. (Ans. 16-8 kW) 1.
A single acting reciprocating pump having cylinder diameter of 150 mm and stroke300 mm is used to raise water through a total height of 30m. Find the power required todrive the pump, if the crank rotates at 60 rpm
A closed tank 5m high contains 2.5 m of water. A nozzle 75 mm in diameter is installed at the side of the tank at a distance 0.5 m. from its bottom. Compute the required air pressure inside the tank to produce 10 hp energy at the nozzle. Cv = 0.95 and Cc = 0.62. * a. 234.65 kPa b. 151.88 kPa c. 183.31 kPa d. 121.23 kPa
In an external gear pump, if the delivery rate is 8 cm3/revolution, the prime mover's speed which is connected to the pump of with 2900 rpm,Determine The pump delivery in terms of litres per minute is
1. Determine the power delivered by the pump in kW 2. Determine the pressure head at point 2 in meters. 3. Determine the pressure head at point 1 in meters Thanks
A pump has a specific speed of 42 and 600 rpm when it delivers 0.01 m3/s. find the head developed by the pump. Answer: 1015.29 ft
A pump draws 20 L/s of water from reservoir A to reservoir B. Assuming f = 0.013 for all pipes, compute the horsepower delivered by the pump. Pump elevation is at datum.Data as follows: Reservoir A to pump. L= 500 m, D = 200 mm, EL. = 15 m Pump to Reservoir B L= 1200 m, D = 150 mm, EL. = 60 m