A single strain gage, placed in the veritical plane on the outer surface and at an angle of 60° to the axis of the pipe, gives a reading at point A of €=250(10^-6). The pipe has an outer diameter of 1 inch and and inner diameter of 0.6 inches and is made of C86100 Bronze. 60° 8 in. 6 in. Determine the principle strains in the pipe at this point.

A single strain gage, placed in the veritical plane on the outer surface and at an angle of 60° to the axis of the pipe, gives a reading at point A of €=250(10^-6). The pipe has an outer diameter of 1 inch and and inner diameter of 0.6 inches and is made of C86100 Bronze. 60° 8 in. 6 in. Determine the principle strains in the pipe at this point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m
Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. 900 mm B 80 mm, 40 mm
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2.0 degrees. The wires are unstretched when the lever is in the horizontal position. Determine the average normal strain developed in wire AH & CG and DF
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which has an outside diameter of 40mm and an inside diameter of 30mm. The length of the brass tube exceeds that of the round steel bar by 0.12mm. Rigid plates are placed on the ends of the tube through which an axial compressive force is applied to the compound bar. Determine the compressive stresses in the bar and tube due to force of 60 kN. Use 200 GPa for modulus of elasticity of steel and 90 GPa for modulus of elasticity of brass.
Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
Cylindrical rod is placed inside. fube of the same length. a the ends of the rod and tube are attached to a rigid support one side and A vigid plate on the other the load on the rod - tube assembly is increased from zero to 26 KN and removed. Draw load-deflection diagram & calculate a the residual stresses in rod & tube Rod Tube Tube 2 A₁ = 46.4mm² Er = 200 Gpa A₁ = 64.5 mm P 100 Gpa = мра ра - 246 MPa 3y = 300 MPa engineering Rod Tube K 800. mm A
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The plate of thickness, t = 5 mm, is loaded with the following stress; oy = 100 MPa, o, = -60 MPa, E = 200 GPa, v = 0.33. If a = 160 mm, and b = 200 mm. B C Calculate the change in the length (mm) of AD. Select the correct response: 0.050
1a) Figure Q1a shows two tubes made of the same material which are riveted together by 50 rivets of 5mm diameter pitched uniformly. The left tube is fixed at section A and the right tube is subjected to an axial tensile force of 20kN. The thickness of both tubes is 5mm. The inner diameter of the right tube is 180mm. Take E-100GPa. Determine, the normal stress in each tube and shear stress in each rivet. the axial tip displacement at section B. Assume the rivets are rigid. the total strain energy stored. () i) iii) Figure Q1a 200mm 1m. Rivet 190mm 1m. B 180mm F=20KN