A single-phase ring distributor is proposed for a newly constructed hospital for COVID 19 Pandemic in Expo center Lahore which feeds on Johar Town Substation. Isolation and Emergency department will be the load points are 20A at 0.8 p.f lagging and 15A at 0.6 p.f lagging respectively. The total impedance of each section Johar Town Substation to Isolation, Isolation to Emergency, and Emergency to Johar Town Substation will be (1 + j 1), (1+ j2), and (1 + j3) ohms respectively. Analyze the ring distributor and Find the total current fed from Johar Town Substation and current in each section.

A single-phase ring distributor is proposed for a newly constructed hospital for COVID 19 Pandemic in Expo center Lahore which feeds on Johar Town Substation. Isolation and Emergency department will be the load points are 20A at 0.8 p.f lagging and 15A at 0.6 p.f lagging respectively. The total impedance of each section Johar Town Substation to Isolation, Isolation to Emergency, and Emergency to Johar Town Substation will be (1 + j 1), (1+ j2), and (1 + j3) ohms respectively. Analyze the ring distributor and Find the total current fed from Johar Town Substation and current in each section.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.36P

See similar textbooks

Similar questions

Q5: A generator is connected through a transformer to a synchronous motor. Reduced to the same base, the per unit subtransient reactances of the generator and motor are 0.15 and 0.35, respectively, and the leakage reactance of the transformer is 0.1 per uint. A three-phase fault occurs at the terminals of the motor when the terminal voltage of the generator is 0.9 per uint and the output current of the generator is 1 per unit at 0.8 power factor leading. Find the subtransient current in per unit in the fault, in the generator, and in the motor. Use the terminal voltage of the generator as the reference phasor and obtain the solution (a) by using the internal voltages of the machines and (b) by using Thevenin's theorem.
Three 15MVA, 30kV synchronous generators A, B, and C are connected via three reactors to a common bus bar, as shown in Figure below. The neutrals of generators A and B are solidly grounded, and the neutral of generator C is grounded through a reactor of 2. Q. The generator data and the reactance of the reactors are tabulated below. A line-to-ground fault occurs on phase a of the common bus bar. Neglect prefault currents and assume generators are operating at their rated voltage. Determine the fault current in phase a. GB Gc Item GA GB Gc 0.25 pu 0.155 pu 0.056 pu 0.20 pu 0.155 pu 0.056 pu 0.20 pu 0.155 pu 0.060 pu 6.0 ? REACTOR Reactor 6.0 6.0
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
A 10,000 kVA, 6.9 kV generator has percentage reactance to positive, negative and zero sequence currents 10%, 7% and 3% respectively and its neutral is grounded solidly. The generator is open circuited and excited to its rated voltage. Calculate the line currents (a) when a single line to ground fault develops on phase 'a' of the generator and (b) when the generator phases b and c are shorted.
Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The generators are rated at 100MVA; 11 KV with subtransient reactance of 25%. The transformers are rated each at 100 MVA, 11/112 KV and have a leakage reactance of 8%. The lines have an inductance of 1 mH/phase/km. Line L1 is 100 km long while lines L2 and L3 are each of 50 km in length. He Load 10 For a 3-phase fault at bus 5, the fault current is equal to 2530A. What the value of the change in the fault current if the length of L1 is reduced to 50 km (i.e. new .value/old value) 1 O 1.0174 0.9965 1.0062 1.0222 0.9867
A generator is rated 100 MVA, 15 kV. It is Y-connected, solid grounded and is operated at rated voltage at no-load and is disconnected from the rest of the system. Its positive and negative sequence reactances are 0.10 p.. and its zero sequence reactance is 0.05 p.. Calculate in ohms of inductive reactance to be inserted in the neutral connection of the generator to limit the fault current for a single line to ground fault to the fault current of a symmetrical three-phase fault.
Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The generators are rated at 100MVA; 11 KV with subtransient reactance of 25%. The transformers are rated each at 100 MVA, 11/112 KV and have a leakage reactance of 8%. The lines have an inductance of 1 mH/phase/km. Line L1 is 100 km long while lines L2 and L3 are each of 50 km in length. 1- For a 3-phase fault at bus 5, the fault current is equal to 2530A. What the value of the change in the fault current if the value of the base voltage is changed to 10 kV (i.e. new value/old value). 2- For a 3-phase fault at bus 5, the fault current is equal to 2530A. What the value of the change in the fault current if the length of L1 is reduced to 50 km (i.e. new value/old value).
A 30 MVA, 13.2KV synchronous generator has a solidly grounded neutral. Its positive, negative and zero sequence impedances are 0.3, 0.4 and 0.05 p.u respectively What value of reactance in p.u. must be placed in the generator neutral so that the fault current for a line to ground fault shall not exceed the rated line current? 0.65 O 0.7 O 0.75 O 0.6 0.68 O 0.63 O 0.8 0.79
Ex.5: A 10 MVA transformer operate at 25% overload, feeds 11 kV busbar through circuit breakers. The 11 Kv busbars through a circuit breaker. The busbars feed outgoing feeders through other circuit breakers, current transformers housed in the transformer and feeder circuit breakers have ratios 525/1 and 352/1 respectively and all sets of current transformer feed induction type over current relays having characteristic for a 100% setting
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
In the shown below power system, both generators G1 and G2 emf’s are equal.All the system data are shown on the system diagram.a) Draw the system diagram in per unit using (MVA)base = 75 and (KV)base =20 KV in the generators side.b) Calculate the three-phase balanced short circuit current (If) at busbar 3 inAmpere and the fault level (MVA)sc in MVA.c) If the fault at busbar 3 is a line-to-line fault, calculate the fault current inAmpere and the fault level (MVA)sc in MVA.