A simply supported composite beam with a 3.6 m span supports a triangularly distributed load of peak intensity go at midspan (see figure part a). The beam is constructed of two wood joists, each 50 mm x 280 mm, fastened to two steel plates, one of dimensions 6 mm x 80 mm, and the lower plate of dimensions 6 mm x 120 mm, (see figure part b). The modulus of elasticity for the wood is 11 GPa and for the steel is 210 GPa 30 mm X 280 mm wood joist 280 mm 6 mm X 120 mm steel plate 18 m (a) (b) If the allowable stresses are 7 MPa for the wood and 120 MPa for the steel, find the allowable peak load intensity go.a when the beam is bent about the z axis. Neglect the weight of the beam. Round to two decimal places.

A simply supported composite beam with a 3.6 m span supports a triangularly distributed load of peak intensity go at midspan (see figure part a). The beam is constructed of two wood joists, each 50 mm x 280 mm, fastened to two steel plates, one of dimensions 6 mm x 80 mm, and the lower plate of dimensions 6 mm x 120 mm, (see figure part b). The modulus of elasticity for the wood is 11 GPa and for the steel is 210 GPa 30 mm X 280 mm wood joist 280 mm 6 mm X 120 mm steel plate 18 m (a) (b) If the allowable stresses are 7 MPa for the wood and 120 MPa for the steel, find the allowable peak load intensity go.a when the beam is bent about the z axis. Neglect the weight of the beam. Round to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b, - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E, - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is E2 - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Your answer has been saved. See score details after the due date. Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n- Attempts: 1 of 1 used Part 2 Determine the area moment of inertia of the transformed section about the z-axis. Answer: in.4
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are bz - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E1 - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is Ez - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n - i
The composite bar, firmly attached to unyielding supports, is initially stress free. What maximum axial load P can be applied if the allowable stresses are 100 MPa for aluminum and 140 MPa for steel? Bronze Steel A = 1800 mm² A = 1125 mm? E = 83 GPa %3D E = 200 GPa %3D P -450 mm- 360 mm·
() If the cross-section of the beam is the composite section shown below, determine the maximum stress in the steel and in the wood (Ewood = 2000 ksi, Eal = 29000 ksi). steel wood wood 10 in. 3 in. 3 in fin.
Q2/A composite beam is of the construction as shown in 50 mm, 50 mm the figure. Calculate the allowable U.D.L. that the beam can Timber carry over a simply supported span of 7 m if the stresses Brass are limited to 120 MN/m² in the Brass and 7 MN/m² in the timber. Modular ratio = 10. I Hoole OS 100 mm 100 mm
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
The working stresses for the manufactured wood beam are 10 MPa in bending and 1.4 MPa in shear. Determine the largest allowable value of the load intensity wo. 25 mm Wo 25 mm - 250 mm 25 mm 3 m 6 m - 200 mm
A composite beam is constructed using a steel plate (15 mm x 145 mm) with two wood beams (75 mm x 145 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M, = 6.85 kN m. Z Steel Wood Calculate the maximum tensile and compressive stresses in the wood and steel if Ew = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for composite beams described in the textbook.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel MPa 1-94 h
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)st 150 MPa and (Gallow)br=200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w 2m Aluminum Brass Steel 40 mm- 10 mm 10 mm 20 mm
A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 230 mm 38 mm 6.5 mm -163 mm- The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) (No Response) 14.06 kN· m
Problem 1- A composite T-beam is built up out of plywood and steel angle sections. The steel angle sections have 100 mm long sides and are 10 mm thick. What is the maximum allowable distributed load, w, if we do not want the materials to go beyond their allowable stresses. Given: For plywood: E = 15 GPa, omax = 8 MPa For steel: E = 200 GPa, oma: 150 MPa %3D %3D > 50 K K100> K 100> 3 m: Cross section (dimensions in mm) 200-