A scientist wearing a circular metal cuff on his wrist moves his hand into a uniform magnetic field of 6T in 0.4s. If the diameter of the cuff is 6cm and the field is at an angle of 45 degrees with the plane of the metal cuff what is the magnitude of the average EMF induced within the band? If the cuff has a resistance of 1OHM what is the induced current then?

A scientist wearing a circular metal cuff on his wrist moves his hand into a uniform magnetic field of 6T in 0.4s. If the diameter of the cuff is 6cm and the field is at an angle of 45 degrees with the plane of the metal cuff what is the magnitude of the average EMF induced within the band? If the cuff has a resistance of 1OHM what is the induced current then?

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter25: Electromagnetic Induction

Section25.1: Electric Current From Changing Magnetic Fields

Problem 3PP

See similar textbooks

Similar questions

A square loop whose sides are 6.0-cm long is made with copper wire of radius 1.0 mm. If a magnetic field perpendicular to the loop is changing at a rate of 5.0 mT/s, what is the current in the loop?
Unreasonable results Frustrated by the small Hall voltage obtained in blood flow measurements, a medical physicist decides to increase the applied magnetic field strength to get a 0.500-V output for blood moving at 30.0 cm/s in a 1.50-cm-diameter vessel. (a) What magnetic field strength is needed? (b) What is unreasonable about this result? (C) Which premise is responsible?
A flat, square coil of 20 turns that has sides of length 15.0 cm is rotating in a magnetic field of strength 0.050 T. If tlie maximum emf produced in die coil is 30.0 mV, what is the angular velocity of the coil?
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
A loop of wire with a radius of 0.16 m and resistance, 47.4 Ohms is in a region with a changing magnetic field that is oriented perpendicular to the loop. If the magnetic field increases linearly from 0.011 T to 0.05 T, over 5.59 x 10-3 s, what is the current in the loop? Please give your answer in Amps.
1.8 Cast-steel Cross-sectional pap1 = 0.5 mm. area -3 cm? 1.6 l4 = 10 cm Silicon iron Cast iron 1.4 Mild steel 1.2 Cross-sectional area 32 ст? 1.0 0.8 Cast iron Cross-sectional area-1.4 cm? = 0.1 mm 0.6 (a) 0.4 0.2A 1000 2000 3000 4000 5000 6000 7000 Magnetic field strength, H(A/m) (b) Figure (1) Silicon Iron uɔ S7 = "1 Flux density, B(T)
A 11.7 cm long rod moves at 3.99 (m/sec). What is the strength of magnetic field if a 94.8 V emf is induced.
The 17.0 cm long rod in the figure below moves at 4.00 m/s. What is the strength (in T) of the magnetic field if a 8.90 V emf is induced?
A 1450 turn coil of wire, 6.16 cm in diameter, is in a magnetic field that drops from 0.723 T to 0 T in 41.9 ms. The axis of the coil is parallel to the field. What is the emf (in V) of the coil?
Problem 3: A loop of wire with radius r = 0.015 m is in a magnetic field with magnitude B as shown in the figure. B changes from B1 = 0.45 T to B2 = 5.5 T in At = 9.5 s at a constant rate. The resistance of the wire is R = 9 Q. B a) Calculate the numerical value of the change in magnetic flux, AO, in T:m2. b) Calculate the numerical value of the average emf, ɛ, induced in the loop in volts. c) Calculate the numerical value of the current induced in the loop, I, in amperes.
A generator has a 46-turn coil with an area of 0.07 m2 that turns at 25.0 rad/s in a 0.48 T magnetic field. What is the current through the coil when the normal to the coil makes an angle of 30o with the magnetic field? The resistance in the coil is 7.84 Ohms. Give your answer in Amperes.
The magnetic field through a single loop of wire 12.0 cm in radius and of 7.5 Ω resistance changes with time as shown in the figure. Calculate the emf in the loop as a function of time.What is the emf at t = 1.0 s? For the sign take the loop in the plane of the paper, and the magnetic field out of the paper. Take clockwise to be positive emf. What is the emf at t = 3.0 s? What is the emf at t = 5.0 s? What is the current at t = 1.0 s?