A resistor of 3 ohms is in series with an inductor of 8 ohms inductive reactance. Thecombination is supplied by a 120-volt RMS sinusoidal voltage. Compute for thecurrent, in amperes, supplied by the source.A resistor of 5 ohms is in series with an inductive coil. The coil has a 3 ohms resistanceand 10 ohms inductive reactance. Find the voltage across the coil, in volts, if supplyvoltage is 120-V RMS sinusoidal voltage.A 5 ohm capacitive reactance capacitor is in series with a 9 ohms resistor. Thecombination is supplied from a 120-V RMS sinusoidal voltage source. Calculate thepower, in watts, taken by the resistorA 10 ohm resistor is connected in series with a load considered as a lossy capacitor.The lossy capacitor has a capacitive reactance of 6 ohms and a resistance of 7 ohms.Calculate the voltage across the load or the lossy capacitor, in volts. Supply voltageis 120-V RMS sinusoidal voltage.

Answered: Image /qna-images/answer/f5e066d2-6bb1-4b74-9da2-1367b26782eb.jpg

A resistor of 3 ohms is in series with an inductor of 8 ohms inductive reactance. The combination is supplied by a 120-volt RMS sinusoidal voltage. Compute for the current, in amperes, supplied by the source.

A resistor of 3 ohms is in series with an inductor of 8 ohms inductive reactance. The combination is supplied by a 120-volt RMS sinusoidal voltage. Compute for the current, in amperes, supplied by the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Define what we mean by “power-factor correction.” For power-factor correction of an inductive load,…

A: Power factor correction means reducing total reactive power of circuit or load. After power factor…

Q: A 60-Hz 220-V-rms source supplies power to a load consisting of a resistance in series with an…

A: Supply voltage is given as Active power P = 1500 W. Apparent power S = 2500 VA. Apparent power is…

Q: Why transient steady in electric circui is important ? O To have a steady state case To know the…

A: In this question we will write about transient state study in circuits...

Q: RMS value ?

A: Given waveform,

Q: What is the load factor? What happens when load factor = 1?

Q: For an ac circuit consisting of a load connected to a Thévenin circuit, is it possible for the load…

A: Yes, it is possible for the load voltage to exceed the Thevenin voltage in magnitude for an AC…

Q: What are the elements which contribute to the cost of the electricity? And discuss how the “load…

A: COST OF ELECTRICITY Different methods of electricity generation can result in a variety of costs,…

Q: A load consists of a 60-ohm resistor in parallel with a 90uF capacitor. If the load is connected to…

Q: -v(t)i(t) -1.5 -1 -0.5 0.5 1.5 1 0 0 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.015 0.018 0.02 0,022…

A: As per the guidelines of bartleyby I need to answer first three subparts only so kindly repost other…

Q: b) A device with characteristics as shown is used to control an 110V AC supply. The load is…

A: The I-V characteristics of a device is given in the question. We need to identify the device. Also…

Q: A current of 4 A flows when a neon lightadvertisement is supplied by a 110-V rms powersystem. The…

A: Let Vrms be the RMS voltage, Irms be the RMS current, theta be the angle between the current and the…

Q: A system is shown in Figure below. The response to a unit step, when K 1, is shown in corresponding…

A: From the figure when the K = 1 the steady-state error from the graph is 0.2 the output is Y(s) and…

Q: Draw a figure that represents one cycle of the AC voltage signal present at a typical household wall…

Q: 8. Two coils are connected in series. With 5 A DC through the circuit, the potential drops across…

A: We need to find out current and power and power factor for the given circuit

Q: d. Write the equation for the power as a function of time. e. You measure the rms current (with a…

A: The given graph is power waveform. What is power equation, voltage equation, current equation.…

Q: V peak to peak, and has a time of 5 ms between consecutive peak and through, at t = 0 is -3.6 V and…

Q: A sinusoidal voltage has a peak value of 15 V, has a frequency of 125 Hz, and crosses zero with…

Q: Derive the formula for the RMS value for the following a)

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: Vpk wt 4n 2n

A: The solution is given below

Q: When connected in series with a pure resistor R with resistance r and inductance L, three pairs of…

Q: A building with inductive loads has the average consumption of 40kW and 26kVAR. At the are location…

A: In this question we need to find a average current , effective impedance and surcharge

Q: Derive the expression for power developed due to wind energy

A: Let v is the speed of wind, d is the height of the blade, Cross section area of blade is given by,…

Q: A dc voltage equal to Vdc V is applied to a resistor of R Ω. Asinusoidal voltage equal to vs V is…

A: Calculating energy delivered to the resistor due to DC voltage source is VDC = Vmax.…

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

A: Given A three phase supply is connected to bridge rectifier V=180 V R=200 ohm

Q: Derive the formula for the RMS value for the following

Q: (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to…

A: Capacitor- capacitors are widely used in electronic circuits to block direct current power while…

Q: A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms. Find the rms…

A: Given data, The value of line-to-neutral rms voltage is VPrms = 440 V. The value of resistance is R…

Q: Reduce the system given in the following figure

Q: )I2(t) Find the mathematical expression for

A: I2(t) Find the mathematical expression for

Q: Find the rms of the below voltage waveform 2.

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: Determine the rms value for each of the waveforms shown in figure below.

A: The root mean square value of any function represents it's effective value affecting the working…

Q: Q3: Find the rms and average current flowing through the heater shown in figure below. The delay…

A: From the single phase AC voltage Regulator

Q: How would you calculate active, reactive and apparent power?

A: In AC Circuits, Voltage and currents are not in the phase. There may be a phase difference between…

Q: A current of 10 A rms flows when a single-phasecircuit is placed across a 220-V rms source.…

A: Write the given values in the question.

Q: a. Derive the expression for the voltage gain, current gain, and power gain in terms of power…

Q: Problem 1 (Source, Load and Battery). In the figure shown, a DC energy source generates power Pe to…

A: Q1 From the given description, The current delivered by the battery can be written in terms of…

Q: Find the RMS value

A: The wave diagram shows the maximum value of the voltage as Vm.

Q: What is the physical meaning of the reactive power and the power triangle? Explain how

Q: a) Write the Biot-Savart Law for a steady current I.

A: A small current carrying conductor of length dl, carrying a current I is an elementary source of…

Q: The average power consumed by a typical kettle with a heating element that has a pure resistance of…

Q: A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void…

A: Given: Dielectric constant εr=4 Internal void thickness d1=1mm Specimen thickness = 1 cm Breakdown…

Q: Find the instantaneous voltage at 200us of the 10Vpk 1kHz sinusoidal source. v(200us) = ? Volts

A: The solution is given below

Q: Add the two voltages below together (phasor voltages are RMS). ?ଵ =60 ? ∠ 0° ?ଶ =80 ?∠ 270° a) What…

A: a) The two voltages are V1 = 60 ∠0° V2 = 80 ∠270° The resultant Voltage = V1…

Q: A transformer outside of a business steps the average voltage down from V1 to V2. The transformer…

A: Transformer: A transformer is a type of passive electrical device that uses electromagnetic…

Q: A sinusoidal voltage is 20 V has a time of 5 ms. peak-to-peak, between consecutive peak and trough,…

A: In this question, We need to determine the general equation of the voltage If peak to peak…

Q: Q6.Using Kirchhoff's current law, find the values of the unknown currents in Figure .below SA

A: To solve above problem, we will use Ohm's law and Kirchhoff's law: Ohm's law state that in a current…

Q: What is the average Power at maximum resistance? Why? What is the effect to the voltage and current…

A: Part 1: The instantaneous power is the multiplication of the instantaneous voltage and the current.…

Q: Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average…

Question

A resistor of 3 ohms is in series with an inductor of 8 ohms inductive reactance. The
combination is supplied by a 120-volt RMS sinusoidal voltage. Compute for the
current, in amperes, supplied by the source.
A resistor of 5 ohms is in series with an inductive coil. The coil has a 3 ohms resistance
and 10 ohms inductive reactance. Find the voltage across the coil, in volts, if supply
voltage is 120-V RMS sinusoidal voltage.
A 5 ohm capacitive reactance capacitor is in series with a 9 ohms resistor. The
combination is supplied from a 120-V RMS sinusoidal voltage source. Calculate the
power, in watts, taken by the resistor
A 10 ohm resistor is connected in series with a load considered as a lossy capacitor.
The lossy capacitor has a capacitive reactance of 6 ohms and a resistance of 7 ohms.
Calculate the voltage across the load or the lossy capacitor, in volts. Supply voltage
is 120-V RMS sinusoidal voltage.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
A resistor R and a capacitor C are connected in series across a 400 V variable ac supply. When the frequency is 40 Hz, it draws 10 A current, and when the frequency is 50 Hz, it draws 15 A current. Find R and C.
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
The below figure shows the waveform of the voltage and current in a purely inductive AC circuit. Voltage Current Using the voltage phasor as the reference, the current phasor Lags by 90° Is in phase with the voltage Leads by 90° Lags and then leads by 160°
Problem Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage source.