A reasonable approximation for the two-dimensional incompressible laminar boundary layer on a flat surface in Figure Q2 on the next page is (2y u = U for ys8 82 where, 8 = Cx'/² and C = const a) Assuming a no-slip condition at the wall, find an expression for the velocity ди ди д8 component v(x, y) for y s 8. (Hint: dx as əx :) b) Also, find the maximum value of v at the station x = 1 m, for the particular case of air flow, when U = 3 m/s and 8 = 1.1 cm.

A reasonable approximation for the two-dimensional incompressible laminar boundary layer on a flat surface in Figure Q2 on the next page is (2y u = U for ys8 82 where, 8 = Cx'/² and C = const a) Assuming a no-slip condition at the wall, find an expression for the velocity ди ди д8 component v(x, y) for y s 8. (Hint: dx as əx :) b) Also, find the maximum value of v at the station x = 1 m, for the particular case of air flow, when U = 3 m/s and 8 = 1.1 cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area Wall thickness- 2mm b. Perimeter of the thin walled tube ABC is a sector with a radius of 50 mm c. Shear flow AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium d. Shear stress e. Angle of twist A R 90° в D 3R
1) a Compressor with a diameter of 0,65 metres and a thickness (t)= 4mm Sigmax= 42 MPA and Sigmay=84MPA Calculate: The pressure P and Maximum In-Plane Shear Stress Tmaxvlak in MPA 2) an element has undergoing a rotation of Theta= 30 degrees Sigmax= 75 MPA and sigma y= 55 MPA. Calculate X', Y' and Txy" in MPA 3) A uniform Beam with a lenght of 2 metres to a-a and forces N=12kn and V=4kn. Calculate the main stresses sigma1 and sigma 2 [in MPA] 4) an element with the given stresses: Sigmax=75 MPA and Sigmay= 55 MPA Calculate the Absolute maximum shear stress in MPA )Tabsmax)
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: F w (x) = E, ( - +4) %3D Ely 8. The value of E is 200,000 Nmm 2 and the values of ly is 20 x 106 mm4 The maximum value of z for the beam cross section is 20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm? Express your answer in Nmm2, as a number to 2 dp, without the units.
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?
Q\Discuss in detail the effect of the boundary condition in the Buckling of hollow shaft.
(c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed lines in the figure. Calculate (i) The normal strain along the centreline OC; (ii) The normal strain along the edge AC; and (iii) The shearing strain between the edges AC and BC. b 0-1 b B 90° 10.001b
A simply supported rectangular aluminium plate has a length a = 5.0 m; and a width b = 2.0 m. It is designed to carry a lateral pressure of 6 MPa. Take E = 120 GPa, v= 0.27, oy = 280MPa and p=2700kg/m³ Determine The minimum required thickness h of the plate(consider the factor of safety n = 1.5); The fundamental frequency of the plate.
0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section of the beam is of T-shape. Determine The shearing stress 20 mm from the top surface of the beam of a section adjacent to the supporting wall. 50 KN 120mm 2 т 20mm 120mm 20mm
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm
2 400 N/mm DY 45° В 2 400 N/mm The square element in the figure is subjected to a biaxial stress of 400 N/mm2 as shown. What is the intensity of normal stress p, on the plane BD? 400 N/mm ww/N 00 2.
A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
2:37 6.00 KB/S A 2M 3M B Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as shown. Each copper rod has an area of 900mm2 and E=120GPA, and the allowable stress is 70MPa. The steel rod has an area of 1200mm2, E=200GPA and the allowable stress is 140MPA. Determine the largest load P which can be supported. Your answer Figure for Problem 2 STEEL 24OMM COPPER COPPER 16OMM 16OMM --