(a) Powder metallurgy (PM) is a net-shape forming process by which fine powdered materials are blended, pressed into the desired shape (compacted), and then heated (sintered) in a controlled atmosphere to bond the contacting surfaces of the particles and establish desired properties. i) Justify the reasons why powder-metal parts are commonly used for machine elements which requiring good tribological characteristics. ii) Compaction is the step in which high pressure is applied to the powders to form them into the desired shapes. The purposes of compaction are to obtain the required shape, density, and particle-to-particle contact. In your opinion, is there any density variation in the compacting of powders? Justify your answer. If your answer is yes, propose appropriate methods to reduce the variation.

(a) Powder metallurgy (PM) is a net-shape forming process by which fine powdered materials are blended, pressed into the desired shape (compacted), and then heated (sintered) in a controlled atmosphere to bond the contacting surfaces of the particles and establish desired properties. i) Justify the reasons why powder-metal parts are commonly used for machine elements which requiring good tribological characteristics. ii) Compaction is the step in which high pressure is applied to the powders to form them into the desired shapes. The purposes of compaction are to obtain the required shape, density, and particle-to-particle contact. In your opinion, is there any density variation in the compacting of powders? Justify your answer. If your answer is yes, propose appropriate methods to reduce the variation.

Physical Chemistry

2nd Edition

ISBN:9781133958437

Author:Ball, David W. (david Warren), BAER, Tomas

Publisher:Ball, David W. (david Warren), BAER, Tomas

Chapter22: Surfaces

Section: Chapter Questions

Problem 22.46E: Early attempts to coat metals with Teflon, poly tetrafluoroethylene, resulted in a polymer layer...

See similar textbooks

Similar questions

4. An alloy has an elastic modulus of 115 GPa. For the alloy, plastic deformation begins at a stress of 275 MPa. (a) If a sample of cross-sectional area 325 mm? is obtained from the alloy, determine the maximum load that may be applied on the sample without plastic deformation. (b) The original sample length is specified as 115 mm, what is the maximum length to which the sample can be stretched without plastic deformation.
In a laboratory, a student calibrates a 25 mL pipette to use throughout asemester. She accidentally breaks the pipette during the fourth of tenexperiments. Suggest what should she do to present reliable findings at the endof the semester.
my topic is "Hazard placards on compressed gases For this assignment, you will be working in a small group to research the scenario indicated in the title of your group and explain how it is dependent on the properties of gases that you learned about in this module. You will compile your research in a short wiki page. The expectations for your group are as follows: • Each group member will research and contribute one source related to the application of gaseous properties to your assigned topic.
Provide the missing conditions
Soil vapor extraction (SVE) is used to remove volatile or-ganic pollutants, such as chlorinated solvents, from soil at haz-ardous waste sites. Vent wells are drilled, and a vacuum pump is applied to the subsurface. (a) How does this remove pollutants?(b) Why does heating combined with SVE speed the process?
A steady-state process to recover crystalline potassium chromate (K,CrOz) from an aqueous solution of this salt is required. Four thousand kilograms per hour of a solution that is one-third K,CrO, by mass is joined by a recycle stream containing 36.4% K2CrO7, and the combined stream is fed into an evaporator. The concentrated stream leaving the evaporator contains 49.4% K,CrO; this stream is fed into a crystallizer in which it is cooled (causing crystals of K,CrO, to come out of solution) and then filtered. The filter cake consists of K,CrO, crystals and a solution that contains 36.4% K,CrO, by mass; the crystals account for 95% of the total mass of the filter cake. The solution that passes through the filter, also 36.4% K,CrO,, is the recycle stream. 1- Draw the flowchart of the system and put all known information. 2- Calculate the rate of evaporation, the rate of production of crystalline K,CrO7, the feed rates that the evaporator and the crystallizer must be designed to handle, and…
Provide the remaining data missing
a) Give any one practical example of adsorption phenomena. b) Mention any FOUR (4) applications of adsorption in chemical analysis.
The Ogallala aquifer described in the Closer Look box in, provides 82% of the drinking water for thepeople who live in the region, although more than 75% ofthe water that is pumped from it is for irrigation. Irrigationwithdrawals are approximately 18 billion gallons per day.(a) Assuming that 2% of the rainfall that falls on an areaof 600,000 km2 recharges the aquifer, what average annualrainfall would be required to replace the water removed forirrigation? (b) What process or processes accounts for thepresence of arsenic in well water?
- = T C 54°F Humid % Explanation O CHEMICAL REACTIONS Percent yield of chemical reactions 2 W |HC|HL| (@F11218HCHIHUSI https://www-awu.aleks.com/alekscgi/x/Isl.exe/10_u-IgNslkr7j8P3jH-IBMBkpcnaFu0F7Uj... FAX S Check بهر 3 * E $ X Gaseous ethane (CH₂CH3) reacts with gaseous oxygen gas (O₂) to produce gaseous carbon dioxide (CO₂) and gaseous water (H₂O). If 0.469 g of water is produced from the reaction of 0.90 g of ethane and 5.2 g of oxygen gas, calculate the percent yield of water. Round your answer to 2 significant figures. 4 0 d R DE C Ś 96 % 5 T 6 G H "4+ & 7 B N U 144 * 00 C | 141 | a A 8 1 D-II ( 9 r K M || a ✓ DDI O s ) B Ⓒ2022 McGraw Hill LLC. All Rights Reserved. Terms of Use | | O F ▬▬▬▬▬▬ fo 1 11² a P MC - MC insert C + 3/5 = prt sc } ♡ 4 Privacy Center Privacy Center | Acces 1 0 Chisom Seve E d 11:10 10/22/20
What procedures can we use to solve this problem?
1. Railroad tracks made of 1025 steel are to be laid during the time of year when the temperature averages 10°C (50°F). If a joint space of 4.6 mm (0.180 in.) is allowed between the standard 11.9-m- (39-ft-) long rails, (a) what is the hottest possible temperature that can be tolerated without the introduction of thermal stresses? (b) If these tracks were going to be laid in the Australian Outback and see temperatures of 150 °F, what would the stress be?