A point on a thin plate is subjected to two successive states of stress. The stresses have magnitude |oz| = 31.5 MPa, |oy| = 45.5 MPa, and Try | = 20.5 MPa. 60° VAΣo↓↑vec O Tyy Determine the resulting state of stress on the element on the right. The rotation angles on the left-hand side of the figure are in relation to the orientation of the element on the righ Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) ? txy

A point on a thin plate is subjected to two successive states of stress. The stresses have magnitude |oz| = 31.5 MPa, |oy| = 45.5 MPa, and Try | = 20.5 MPa. 60° VAΣo↓↑vec O Tyy Determine the resulting state of stress on the element on the right. The rotation angles on the left-hand side of the figure are in relation to the orientation of the element on the righ Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) ? txy

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
At a point on the surface of a pressurized cylinder, the material element is subjected to stresses; σx = 60 MPa, σy = - 40 MPa, and τxy = - 30 MPa. Construct Mohr’s circle, then use it to determine the following: Do not use the equations of transformations.1- The principal stresses and the maximum shear stress.2- Show these stresses on sketches of properly stress elements.3- A point on the circle where the element is only subjected to pure shear stress. Calculate the value of that pure shear stress.
The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 15 ksi 23 ksi 14 ksi
A point on a thin plate is subjected to the two stress components as shown in Figure 7. Determine the resultant state of stress represented on the element oriented as shown on the right. “L.. 100 MPa Oy 160 MPa Txy |45° Ox + 30 100 MPa
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr's circle representing the complete state of stress of the element, i.e. show prinicpal stresses (01,02), maximum shear stresses (Tmax), principal direction (0p), original orientation, and original stresses (Ox, Oy, Txy). (b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shear stress. Oy = -50 MPa Txy 20 MPa Ox = -150 MPa