A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
Q: A ball is dropped from rest at the top of a 60 meters tower. A horizontal wind gives it a constant h...
A:
Q: An eccentric load P = 200 kN is placed at an eccentricity of 180mm from the x-axis and 300mm from th...
A:
Q: Problem 2- 18 Determine the shear force on the most stressed fastener in Figure 2 - 31 if P = 1,000 ...
A:
Q: IV. PROBLEM SOLVING *** Sign Convention : Positive values are for vertical forces upward and horizon...
A: note: we bartleby experts are required to answer only first 3 sub parts of the question. So please s...
Q: bosin ond averefe(peufrveloi ty 7the Assipmnt I efample Towo million titves gwata paclay of paninf T...
A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question s...
Q: 2 is growing at 2 ppm/yr, fossil and cement emission are 9 GtC/yr and the air borne fraction is 38 p...
A: Given:- atmospheric CO2=2ppm/year fossil and cement emission =9 GtC/yr To find:- net carbon emission...
Q: d, e =0, determine the horizontal sightline offset (HSO) that a large billboard can be placed from t...
A: Given:- radius of 800 ft posted speed limit of 35 mi/h e =0, To find:- the horizontal sightline o...
Q: An 8 meter high granite column sustains an axial compressive load of 500kN. If the column shortens 0...
A:
Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...
A:
Q: 10 ft 4 ft 4 ft 10 ft 10 ft B. 600 lb 800 lb
A:
Q: A vehicle is passing trough a simple curve and the drive's reaction time is 2.5 sec. towards a build...
A:
Q: A calibration test of a 12.5 mm diameter circular sharped-edged orifice in a vertical side of a larg...
A:
Q: Question: Calculate the kinetic energy in joules of a 150 lb jogger (68.1 kg) traveling at 12.0 mile...
A: Introduction : The jogger mass and velocity through jogger is moving is given in question . With hel...
Q: A fully saturated soil mass has specific gravity of 2.5 void ratio 0.45 .Determine water content
A:
Q: A tank that has Cylindrical shape with an inside diameter of 120 feet and a depth of 60 feet . wall...
A: To determine the weight of the concrete storage tank at various given states and calculate the beari...
Q: a) SF A C E F A B C E BM b) SF A C E F A E F BM c) SF A B C E A В C E F BM d) SF A C E F A B C E F B...
A:
Q: Tabulation: Trial Mass of cement (gm) Mass of water (gm) Penetration (mm) | Water-cement ratio (%) 1...
A: We are given the data from the consistency test. To calculate the water cement ratio for the normal ...
Q: Determine the hoop and longitudinal stresses set up in a thin book shell of circular cross-section, ...
A: Given data : The value of modulus of elasticity E=210 GN/m2 The value of internal diameter d=1.3 m T...
Q: answer letter d only
A:
Q: 4. The boat's position during the interval of time from t = 2s to t = 10 s is given by s = 4t + 1.6t...
A:
Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...
A:
Q: The excavated material has a wet unit weight of 1,510 kg/ cu metre and a dry unit weight of 1,398 cu...
A:
Q: zoology graduate student is provided with a bow and arrow tipped with a syringe of sedative and is a...
A: The given data is: Find initial speed of arrow, =launching angle=45 deg g=9.81 m/sec2 R=range of arr...
Q: Problem 1. Determine the following unknowns on the beam shown below using Double Integration Method....
A:
Q: A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tensi...
A:
Q: Y 2"I X- 12" 2"| 4" 4" | 2"|
A:
Q: ully welded together. The PL16×380 and PL12X500 for the
A: the flexural strength is given by F =PLbd2where . p = load on beam L = length b =...
Q: SITUATION 2. A DISCHARGE OF 10 m3/s FLOWS THROUGH A PIPE SYSTEM OF DIAMETER 1m. 2. WHAT SHOULD BE TH...
A:
Q: A rectangular block of a material with a modulus of rigidity of FN ksi is bonded to two rigid horizo...
A:
Q: The following are steel design concepts. 1. A member is selected that has cross-sectional properties...
A: question is related to various design theory limit state , lrfd and allowable stress design are var...
Q: If the distance two places on the map is 12cm, with the map scale of 1:2,000,000,what is the ground ...
A: Given data, Map scale = 1:2,000,000 Distance of 2 places on map = 12 cm
Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load...
A:
Q: All answers must be in STORED VALUES and the final answer must be in four (4) decimal places. ANSWER...
A: We will find water content in each case. Water corresponding to 25 blows is liquid limit. For plasti...
Q: How many correct experiments do we need to disprove a theory
A: A theory is a hypothetical model which is developed based on assumptions or certain rules assumed by...
Q: A hydroelectric facility extracts power from a reservoir at an elevation of 800 m, discharging into ...
A: given data Length of penstock=1650 m dia of pipe = 0.8 m k=3 c=1500 flow rate of turbine = 3.5 m3 / ...
Q: URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by ste...
A:
Q: 2.57 In Fig. P2.57 pipe A contains carbon tetrachloride (SG 1.60) and the closed storage tank B cont...
A:
Q: Determine the Reactions +1.5 m--1.5 m- 3 m 3 m 4 m C 2 m 4 m EN kN 2 m SN kN В
A: Determine reactions at support
Q: Question: Calculate the kinetic energy in joules of a 150 lb jogger (68.1 kg) traveling at 12.0 mile...
A: Given data : The mass of jogger m=68.1 kg The velocity of jogger V=5.36 m/s Required : Kinetic ene...
Q: The total length of a first class lever is 9.0 ft. This is used to move a load of 390 lbs, as pictur...
A: This question is related to the Engineering Mechanics.
Q: Suppose a pre-stressed concrete bridge project has completed its engineering design stage and ready ...
A: i) For the same section of Steel girders, live loads can be increased or decreased. It's depandency ...
Q: A bronze bar is fastened between a steel bar and aluminum bar as shown. Find the largest value of P ...
A:
Q: Problem 1. Determine the following unknowns on the beam shown below using Double Integration Method....
A:
Q: A 35-feet simply-supported floor beam, made of ASTM A572 Gr. 50 (Fy = 50 ksi) W18x50 hot-rolled sect...
A: We have to determine the adequacy of the beam to carry the given loads using IBC limits for satisfyi...
Q: A pin-jointed frame is shown in the figure below. The cross-sectional area of all members is 100 mm?...
A: Using unit load method
Q: 10 ft 4 ft 4 ft 10 ft 10 ft Y A 600 lb 800 lb
A:
Q: Determine the Reactions 10 k 6k B D 20 ft MN lb/ft A 30 ft 15 ft 10 ft-10 ft--
A:
Q: Flexibility matrix of the beam shown below is 1 [F]= 3EI 2 사 A If the support B settles by one unit ...
A:
Q: There are four rain gauge stations existing in the catchment of a river. The average annual rainfall...
A:
Q: Consider the pin-jointed truss as shown in figure below: A B D 30° 45° 90° 60° Coordinate direction ...
A:
Trending now
This is a popular solution!
Step by step
Solved in 3 steps
- A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL ½ x 6 The design strength based on yielding is nearest to: The design strength based on rupture is nearest to: The design strength for LRFD is nearest to: The allowable strength based on yielding is nearest to: The allowable strenath based on rupture is nearest to: The allowable strength for ASD.7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2
- A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mmISA 100 x 100 x 10mm (Cross sectional area = 1908mm2) serves as tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm2 the tensile strength of the member can be taken to be approximately A ISA 100x100×10 Gusset Plate BA 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
- TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N Next
- sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the maxA 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the critical net area of the connection shown. Determine the design tensile strength of the section based on yielding of the gross area.Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2