A piston slider crank mechanism is shown below. The connecting rod having a length of 1125 mm enables the rotational motion generated by the crank with a diameter of 500 mm to the transnational motion of the piston. The crank is turning at 403 rpm. At the given instant shown, find the angular velocity of the connecting rod when the angle of the crank is 57° from the horizontal axis. Crank Connecting Rod Piston Cylinder

A piston slider crank mechanism is shown below. The connecting rod having a length of 1125 mm enables the rotational motion generated by the crank with a diameter of 500 mm to the transnational motion of the piston. The crank is turning at 403 rpm. At the given instant shown, find the angular velocity of the connecting rod when the angle of the crank is 57° from the horizontal axis. Crank Connecting Rod Piston Cylinder

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter13: Rotation Ii: A Conservation Approach

Section: Chapter Questions

Problem 32PQ

See similar textbooks

Similar questions

A uniform disk of mass 500 kg and radius 0.25 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim fo the disk and pulled with a force of 10 N. (a) How much work has the force done at the instant the disk has completed three revolutions, starting from rest? (b) Determine the torque due to the force, then calculate the work done by this torque at the instant the disk has completed three revolutions? (c) What is the angular velocity at the instant? (d) What is the power output of the force at that instant?
Small bodies of mass m1 and m2 are attached to opposite ends of a thin rigid rod of length L and M. The rod is mounted so that it is free to rotate in a horizontal plane around a vertical axis (see below). What distance d from m1 should the rotational axis be so that minimum amount of work is required to set the rod rotating at an angular velocity ?
Repeat the preceding problem replacing the marble with a hollow sphere. Explain the new results.
A cord is wrapped around the rim of a solid cylinder of radius 0.25 m, and a constant force of 40 N is exerted on the cord shown, as shown in the following figure. The cylinder is mounted on frictionless bearings, and its moment of inertia is 6.0kgm2 . (a) Use the work energy theorem to calculate the angular velocity of the cylinder after 5.0 m of cord have been removed. (b) If the 40-N force is replaced by a 40-N weight, what is the angular velocity of the cylinder after 5.0 m of cord have unwound?
A uniform rod of mass 1.0 kg and length 2.0 m is free to rotate about one end (see the following figure). If the rod is released from rest at an angle of 60 with respect to the horizontal, what is the speed of the tip of the rod as it passes the horizontal position?
An electric sander consisting of a rotating disk of mass 0.7 kg and radius 10 cm rotates at 15 rev/sec. When applied to a rough wooden wall the rotation rate decreases by 20 . (a) What is the final rotational kinetic energy of the rotating disk? (a) How much has its rotational kinetic energy decreased?
A horizontal beam of length 3 m and mass 2.0 kg has a mass of 1.0 kg and width 0.2 m sitting at the end of the beam (see the following figure). What is the torque of the system about the support at the wall?
Calculate the torque of the 40-N force around the axis through O and perpendicular to the plane of the page as shown below.
Review. A piece of putty is initially located at point A on the rim of a grinding wheel rotating at constant angular speed about a horizontal axis. The putty is dislodged from point A when the diameter through A is horizontal. It then rises vertically and returns to A at the instant the wheel completes one revolution. From this information, we wish to find the speed v of the putty when it leaves the wheel and the force holding it to the wheel. (a) What analysis model is appropriate for the motion of the putty as it rises and falls? (b) Use this model to find a symbolic expression for the time interval between when the putty leaves point A and when it arrives back at A, in terms of v and g. (c) What is the appropriate analysis model to describe point A on the wheel? (d) Find the period of the motion of point A in terms of the tangential speed v and the radius R of the wheel. (e) Set the time interval from part (b) equal to the period from part (d) and solve for the speed v of the putty as it leaves the wheel. (f) If the mass of the putty is m, what is the magnitude of the force that held it to the wheel before it was released?
Repeat the preceding problem replacing the marble with a solid cylinder. Explain the new result.
Given the disk and density in Problem 11, derive an expression for the rotational inertia of this disk around an axis at theedge of the disk and perpendicular to the disks surface.
Two flywheel fo negligible mass and different radii are bounded together and rotate about common axis (see below). The smaller flywheel of radius 30 cm has a cord that has a pulling force of 50 N on it. What pulling force needs to be applied to the cord connecting the larger flywheel of radius 50 cm such that the combination does not rotate?