A piece of plywood in which several holes are being drilled successively has been secured to a workbench by means of two nails. Knowing that the drill exerts a 12-N·m couple on the piece of plywood, determine the magnitude of the resulting forces applied to the nails if they are located (a) at A and B, (b) at B and C, (c)

A piece of plywood in which several holes are being drilled successively has been secured to a workbench by means of two nails. Knowing that the drill exerts a 12-N·m couple on the piece of plywood, determine the magnitude of the resulting forces applied to the nails if they are located (a) at A and B, (b) at B and C, (c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pulleys A and B are mounted on bracket CDEF. The tension on each side of the two belts is given as TÃ1 = 126 lb, TẠ2 = 160 lb, TB₁ = 210 lb, and TB2 = 150 lb. Replace the four forces with a single equivalent force, and determine where its line of action intersects the bottom edge of the bracket. 2 in. 1 in. C F r = 2 in. r= 1in. -6 in- TA1 lb A -6 in.- TA2 lb B D E 4 in. The resultant force R is 352.66 lb x 22.3 The point d where the resultant force intersects the line EF is $25° TB1 lb 125° 2.8 TB2 lb in.
A machine component is subjected to the forces and couples shown. The component is to be held in place by a single rivet that can resist a force but not a couple. For P hole if it is to be located (a) on line FG, (b) on line GH. 0, determine the location of the rivet '120 N 240 mm 200 N 70° 15° E 50 mm 42 N-m 80 N 520 mm 40 N-m 180 mm В 50 mm 50 mm → 640 mm
Pulleys A and B are mounted on bracket CDEF. The tension on each side of the two belts is given as TÃ1 = 126 lb, TẠ2 = 160 lb, TB₁ = 210 lb, and TB2 = 150 lb. Replace the four forces with a single equivalent force, and determine where its line of action intersects the bottom edge of the bracket. 2 in. 1 in. C F r=2 in. r= 1 in. -6 in- TA1 lb A -6 in.- TA2 lb B D E 4 in. The resultant force R is 352.66 lb x 22.3 The point d where the resultant force intersects the line EF is $25° TB1 lb 125° 2.8 TB2 lb in.
Show FBD and complete solution. A machine component is subjected to the forces and couples shown. The component is to be held in place by a single rivet that can resist a force but not a couple. For P = 60 N, determine the location of the rivet hole if it is to be located (a) from G on line FG, (b) from G on line GH.
Q6 A machine component is subjected to the forces and couples shown. The component is to be held in place by a single rivet that can resist a force but not a couple. The location of the rivet hole on line FG and line GH is... 120 N 240 mm 200 N 70° 15 H 50 mm 42 Nm 180 N 520 mm C 60 N 180 mm F |B -50 mm 40 Nm iG A 50 mm 640 mm
Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 50 lb A View C Detail (clearances exaggerated) 14" 50 lb 14" B. Q4) A commercial airliner with four jet engines, each producing 90 kN of forward thrust, is in a steady, level cruise when engine number 3 suddenly fails. Determine and locate the resultant of the three remaining engine thrust vectors. Treat this as a two-dimensional problem. 4 90 kN 9 m 12 m 12 m 90 kN 9 m 90 kN 1 Good luck
Q2:In the design of the lifting hook the action of the applied force F at the critical section of the hook is a direct pull at B and a couple. If the magnitude of the couple is 40 lb-ft, determine the magnitude of F
Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 1"- A 50 lb A C View C Detail (clearances exaggerated) 14" 50 lb 14"
Determine the horizontal and vertical components of force that the pins at A and B exert on the frame. 4.1 The magnitude of the horizontal component Ax at the hinged support A is Blank 1 kN. 4.2 The magnitude of the vertical component Ay at the hinged support A is Blank 2 kN. 4.3 The magnitude of the horizontal component Bx at the hinged support B is Blank 3 kN. 4.4 The magnitude of the vertical component By at the hinged support B is Blank 4 kN.
3.74 A piece of plywood in which several holes are being drilled successively has been secured to a workbench by means of two nails. Knowing that the drill exerts a 12-N.m couple on the piece of plywood, determine the magnitude of the resulting forces applied to the nails if they are located (a) at A and B, (b) at B and C, (c) at A and C. Pia D2 74 A 450 mm B Page 132 240 mm
4. The rigid link is supported by a pin at A, a steel wire BC having an unstretched length of 300 mm and cross-sectional area of 20 mm², and a short aluminum block having a length of 100 mm under no load and cross-sectional area of 40 mm². If the link is subjected to a vertical force of 550 N as shown, determine the force in wire BC and the aluminum block, and the rotation of the link about pin A. Est = 200 GPa, EA = 70 GPa. 300 mm B 200 mm 550N 250mm D A 250 mm 100 mm
Q.2. Force P is acting in the negative y-direction and has a magnitude of 120 N, and force Q is acting in the negative z-direction and has a magnitude of 225 N. Given this loading, solve for the forces in members AB, BC, EC, ED and AD. A 0.6 m 3 m B 0.6 m 2.25 m 1.2 m 0.75 m