A particular furnace is shaped like a section of a cone. The top surface of the furnace is uniformly heated by a resistance heater. During operation, the top surface is measured to be 800 K and the power supplied to the resistance heater is 1750 W/m². The sidewall of the furnace is perfectly insulated with ε = 0.2. If the emissivity of the top and bottom surfaces are ε = 0.5 and ε = 0.7, respectively, determine the temperatures of the sidewall and the bottom surface of the furnace. =

A particular furnace is shaped like a section of a cone. The top surface of the furnace is uniformly heated by a resistance heater. During operation, the top surface is measured to be 800 K and the power supplied to the resistance heater is 1750 W/m². The sidewall of the furnace is perfectly insulated with ε = 0.2. If the emissivity of the top and bottom surfaces are ε = 0.5 and ε = 0.7, respectively, determine the temperatures of the sidewall and the bottom surface of the furnace. =

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.61P

See similar textbooks

Similar questions

Determine the rate of radiant heat emission in watts per square meter from a blackbody at (a) 15C, (b) 600C, and (c) 5700C.
Define Emissivity of some materials at 300 K.
Radiation from a small opening from an isothermal enclosure can be considered as _______.
A 2-m-internal-diameter double-walled spherical tank is used to store iced water at 0°C. Each wall is 0.5 cm thick, and the 1.5-cm-thick air space between the two walls of the tank is evacuated in order to minimize heat transfer. The surfaces surrounding the evacuated space are polished so that each surface has an emissivity of 0.15. The temperature of the outer wall of the tank is measured to be 20°C. Assuming the inner wall of the steel tank to be at 0°C, determine (a) the rate of heat transfer to the iced water in the tank and (b) the amount of ice at 0°C that melts during a 24-h period.
A concentric cylinder with outer and inner radii of 8 cm and 6 cm, respectively, has length of 1 mwith emissivities of the inner and outer radii at 0.4 and 0.6, respectively. Determine the heattransfer from the outer cylinder to the inner cylinder if the inner and outer temperatures are400K and 600K, respectively.
Two very large parallel plates are kept at uniform temperatures T1=800 K and T2=500 K, and have emissivities ε1=0.2 y ε2=0.7, respectively, as shown in the figure. Determine the net rate of radiation heat transfer between the two surfaces per unit surface area of the plates.
2. A thin aluminum sheet with an emissivity of 0.15 on both sides is placed between two very large parallel plates, which are maintained at uniform temperatures T1 = 900 K and T2 = 650 K and have emissivities ?1 = 0.5 and ?2 = 0.8, respectively. Determine the net rate of radiation heat transfer between two plates per unit surface area of the plates and compare the result with that without the shield
Explain the following terms related to the radiation mode of heat transfer: Black body, emissive power, monochromatic emissive power, gray body, white body and opaque body.
According to an Atomic Energy Commissionreport, a hydrogen bomb can be approximated as a large fireball at a temperature of 7200 K. You are to assess theimpact if such a bomb exploded 5 km above a city. Assumethe diameter of the fireball to be 1 km, and the blast to last15 s. Investigate the level of radiation energy people, plants,and houses will be exposed to and how adversely they will beaffected by the blast.
A radiation shield that has the same emissivity 3 on both sides is placed between two large parallel plates, which are maintained at uniform temperatures of T1 = 650 K and T2 = 400 K and have emissivities of E1 = 0.6 and E2 = 0.9, respectively. Determine the emissivity of the radiation shield if the radiation heat transfer between the plates is to be reduced to 15 percent of that without the radiation shield
Imagine you have two concentric, coaxial cylindrical tubes with an evacuated annular space, with equal lengths L. The outer radius of the inner cylinder is r, and the inner radius of the outer cylinder is R. If we want to minimize the self-viewing factor of the inner surface of the outer cylinder, which of the following geometric changes would you suggest? r is fixed, decrease R with fixed R and L, decrease r with fixed r and R, decrease L R is fixed, increase L r is fixed, increase R
a) Define Stefan-Boltzmann Law and emissivity. b) Is there any surface whose emissivity value is greater than 1? If no, explain the reason.