A load of lkW is connected across a 10 V Zener regula- tor as shown in Fig. 54. 41. The zener current can vary between 5mA to 55mA while maintaining the voltage constant. Find the minimum and maximum voltage level at input. 6. 500 ww Vin Tio v 8 1 K (Electronic Devices and Circuits, Nagpur Univ. Summer, 2004) A 24V, 600 mW zener diode is used for providing a 24V stabilized supply to a variable load. If the input voltage is 32V, calculate (i) the value of series resistance required. (ii) diode current when the load is 1200 2 7. Fig. 54.41

A load of lkW is connected across a 10 V Zener regula- tor as shown in Fig. 54. 41. The zener current can vary between 5mA to 55mA while maintaining the voltage constant. Find the minimum and maximum voltage level at input. 6. 500 ww Vin Tio v 8 1 K (Electronic Devices and Circuits, Nagpur Univ. Summer, 2004) A 24V, 600 mW zener diode is used for providing a 24V stabilized supply to a variable load. If the input voltage is 32V, calculate (i) the value of series resistance required. (ii) diode current when the load is 1200 2 7. Fig. 54.41

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Describe the operating principle and characteristics of a typical Zener diode found in the market place, including examples of their common applications. The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
A germanium diode is connected to a load resistance of 1.5 kQ and is supplied with 12-V such that the diode will be forward biased. What is the voltage across the diode? * O A. approximately 12 V O B. approximately 0.7 V O C. approximately 0.3 V O D. lack of data and can't be solved
A silicon diode with a forward resistance of 10Ω is connected in series with a 500Ω resistor. If an A.Cvoltage of 20V peak is connected across the series combination of the diode and the resistor what willbe the peak value of the current through the diode and the peak output voltage? What will be the peakvalue of the current through the diode and the peak output voltage if the diode were ideal?
7. For a certain 12 V zener diode, a 10 mA change in zener current produces a 0.1 V change in zener voltage. The zener impedance for this current range is a. 12 b. 100 Q c. 10 Q
Given the circuit design for a Zener diode regulator in the previous question, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 13 V, the load current il varies between 2 mA and 47 mA, and the diode is an ideal 4 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
For the diode circuit to the right 8002 a V 1002 b 40mA 0.001V' a) To the left of points a and b, find the load-line relation by expressing the current, I with voltage, V. HINT: Write KCL equation for the circuit diagram and write I in terms of V from that KCL equation. This will be your load-line equation. b) Assume the diode has the following characteristic, using the load-line relation you found in (a), determine the operating voltage, V and current, I for the circuit. ip (mA) 20 15 10 5 Vp (V) 3.0 0.5 '1.0 1.5 2.0 2.5
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
How do you identify the anode of an unmarked diode? When the forward current of a diode increases, its forward resistance The current flowing in a reverse-biased diode circuit is extremely while the resistance of the diode is extremely The Vz of a zener diode will fairly constant even if the power supply voltage The series resistor Rs is used with the zener diode to the zener current Iz to a level.
In the circuit shown below, the Zener diode operates at 16 V and its power rating is Pr=5 W. The zener diode needs a minimum of 0.1 A to operate. If V, = 60 V, then R; can vary between: R ww a. 140.80 Ohm, 440.00 Ohm O b. 151.80 Ohm, 451.00 Ohm O c. 129.80 Ohm, 429.00 Ohm O d. 163.80 Ohm, 463.00 Ohm
In the circuit shown below. Let Vm-35 V and i-20 mA and VpQ -0.7 V: iD 3 kQ 0.8 kO Vmcos(@t)V For t Os, the current in the diode equals: Oa. 0 mA Ob. 4 mA Oc. 2 mA Od. 6 mA If t = T/4, then the current in the diode equals: Oa. 6.29 mA Ob. 5.03 mA Oc. 4,03 mA Od. 7.86 mA If t = T/2, then the current in the diode equals: Oa. 15.24 mA Ob. 13.24 mA Oc. 19.24 mA Od. 17.24 mA
Question 1: In the circuit shown below, the output (Vo = 10V Max.) Unipolar. The frequency of Primary is 60 Hz. The diodes are Silicon with VD = 0.7V. a. Sketch the output without a Capacitor. b. Determine Voc without a Capacitor. c. Sketch Vs (at the Secondary). d. Determine Voc with a Capacitor of 10 uF across RL. e. Determine the RMS Value of Vp (at the Primary). f. PIV (Peak Inverse Voltage). 10:1 Output C. 22 k1 All diodes are IN4001. | 00000
Find the Voltage V2 of the Circuit below. Consider all of the Diodes as Silicon. Find the PIV of the Circuit below. Consider all of the Diodes as Germanium.