A linear circuit has a single supply voltage of 2 V. The input current from that source is 2 mA, and the output current is io = (n+1) mA a) If the input voltage changes to 5 V what is the new output current? b) If the output current is doubled from its original value, what is the new input voltage? c) What is the new input current for part b?

A linear circuit has a single supply voltage of 2 V. The input current from that source is 2 mA, and the output current is io = (n+1) mA a) If the input voltage changes to 5 V what is the new output current? b) If the output current is doubled from its original value, what is the new input voltage? c) What is the new input current for part b?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal light
What is CEMF?
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Can you help me with this homework problem? Constant voltage drop is Vd=0.7 What is the output volts of V? What is the current I going through the resistor? What is the diode current Id2? What is the diode current Id1? What are the states of two diodes D1 and D2?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
9. The three terminals of an SCR are a. E,B,C b. A,K c. A,K,G d. MT1,MT,G 10. When an SCR is turned on, the anode to cathode voltage is approximately a. 6 V b. 0.7 V c. 0 V d. none of these
Comment about the behavior of given Circuit and suggest a name for it. Decrease Indent input Q T FF Q' CLK
A full-wave bridge rectifier is to be designed to produce a peak output voltage of 10 V, deliver 100 mA to the load, and produce an output with a ripple of not more than 7.5 percent. Assume that the frequency of the source is 50 Hz, and that a constant drop voltage model with Vp = 0.7 V is t of used. D1 D2 vs(1) RL vz(?) D3 D4 Source Rectifier Load a) Calculate the needed value of the load resistor R1. 1 b) Calculate the peak value of the voltage source which should be used V (t). [ c) What will be the value of the ripple voltage V7 [ d) Calculate the value of the required capacitor C. [ e) Explain in your own words the difference between the output with and without using the capacitor in the circuit above.
#4(a) An 8.2 V (8.2 V at 25 °C) has a positive temperature coefficient of 5.4 mV/°C. What is the output voltage if the temperature rises to 90° C? Page | 4 b) Name two applications of the Zener Diode
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to c 20:5A L VI-DC20V 220V omsh T 0.01 F 0.02 F 0.0167 F None of the above euer