A laminated plastic beam of square cross section is built up by gluing together three strips, each 10 mm by 30 mm in cross section. The beam has a total weight of 3.6 N and is simply supported with span length L = 360 mm. 30 mm 9.01 15.62 Considering the weight of the beam (q) calculate the maximum permissible CCW moment M (N-m) that may be placed at the right support if the allowable bending stress in the plastic is 8 MPa. 25.33 10 mm 10 mm 30 mm $10 mm 2.67 9 L

A laminated plastic beam of square cross section is built up by gluing together three strips, each 10 mm by 30 mm in cross section. The beam has a total weight of 3.6 N and is simply supported with span length L = 360 mm. 30 mm 9.01 15.62 Considering the weight of the beam (q) calculate the maximum permissible CCW moment M (N-m) that may be placed at the right support if the allowable bending stress in the plastic is 8 MPa. 25.33 10 mm 10 mm 30 mm $10 mm 2.67 9 L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
If the beam is subjected to an internal moment of M = 30 kN-m determine the compressive bending stress in MPa on the top surface of top flange A. 50 mm 50 mm 10 mm M 150 mm 15 mm
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
600 -400- 600 800 G| P2 P3 E F Tha at y pnywty i A - 100 mm E - 200 GPa A- 150 mm E- 200 GPa A130 mm E- 70 GPa 700 A- 50 mm E- 83 GPa P1 d. 30° o B 500 All dimensions are in millimeters.
A two-dimensional beam structure or frame (ABCD, shown below) has a concentrated load, P, acting on Point D. You can assume that the connections at B and C have sufficient strength to react the applied load and that loads and moments are transferred between the beams. You can assume that the members have a constant cross-section and that El-constant. B A 2m y L. C P-3kN D 2m In order to evaluate the design you must: (a) Sketch the deformed shape of the frame, solve the reaction forces and construct the bending moment diagram for the frame. (b) Use any method to determine the vertical deflection at Point D. Ensure that you clearly explain your approach and show your final answer. Clearly state any assumptions made. (c) If the bending rigidity, El, of the frame between Point B and Point C was doubled. What effect would this have on the resulting horizontal deflection at point D. Ensure that your answer is supported by suitable reasoning, calculations and/or sketches.
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Calculate the support reaction at roller support A
Q1/ A thin-walled cantilever has a constant cross-section of uniform thickness with the dimensions shown in Figure. It is subjected to a system of point loads acting in the planes of the walls of the section in the directions shown. Calculate the direct stresses according to the basic theory of bending at the points 1,2 and 3 of the cross-section at the built-in end along the beam. 50N 2 mm 50 N 80N 2 mm 100 mm 2 36 mm 80 mm 24 mm
2max 1 max A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a moment M, is applied, what is the value of 0₁/0... It is given that both the metals will bend separately about their own neutral axis. Also draw bending strain and bending stress diagram. Mo Mo at th Jicc E₁, I, E2, 12 d₁ d₂