A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass ofthe ladder is halfway along it. For the ladder to be in mechanical equilibrium: Write down equations for the total r- and y-components of the 5 forces acting on the ladder

A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass ofthe ladder is halfway along it. For the ladder to be in mechanical equilibrium: Write down equations for the total r- and y-components of the 5 forces acting on the ladder

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The 40-kg homogeneous disk is resting on an inclined friction surface. (a) Compute the magnitude of the horizontal force P. (b) Could the disk be in equilibrium if the inclined surface were frictionless?
Determine the smallest horizontal force P that would push the homogeneous cylinder of weight W over the curb. Neglect friction.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
Find the vertical force P that will hold the linkage in the position =40. The spring of stiffness k=3kN/m is unstretched when =0. The length of each link is L=200mm. Neglect the weights of the links.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.