A horizontal cantilever beam, made of steel, is pin-jointed with a vertical brass rod at the end B, as shown in Figure 3. The end C of the rod is pin-jointed to the upper wall. A uniformly distributed load w and a point load P are applied on the beam and rod, as shown. The second moment of area ofthe beam / = 2 x 106 mm4 and the Young's modulus of steel Esteel = 210 GPa. The brass rod has diameter 5 mm and the Young's modulus of brass Eprass= 110 GPa. Under the current loads, the brass rod is extended by 2 mm.600 mm1 A800 mmP= 2 kNFigure 3 34. Determine the axial tensile force F, in the brass rod:OA. F, = 3188.45 NOB. F, = 4592.32 NOC. F, = 6429.97 NOD. F, = 7295.83 N35. When superposition method is applied to solve this beam deflection problem, determine the deflection of the beam at the end B caused by the tensile force F, only:OA. – 1.258 mmOB. – 2.965 mmOC. - 3.774 mmOD. – 4.832 mm36. When superposition method is applied to solve this beam deflection problem, determine the deflection of the beam at the end B caused by the load P only:OA. – 0.339 mmOB. – 0.572 mmOC. - 0.813 mmOD. - 1.635 mm37. Determine the magnitude of the load w:OA. w = 24.51 N/mmOB. w = 28.77 N/mmOC. w = 38.93 N/mmOD. w = 47.36 N/mm

Given data Modulus of elasticity Length Diameter Loading Deflection

A horizontal cantilever beam, made of steel, is pin-jointed with a vertical brass rod at the end B, as shown in Figure 3. The end C of the rod is pin- jointed to the upper wall. A uniformly distributed load w and a point load P are applied on the beam and rod, as shown. The second moment of area of the beam / = 2 x 106 mm4 and the Young's modulus of steel Esteel = 210 GPa. The brass rod has diameter 5 mm and the Young's modulus of brass Eprass = 110 GPa. Under the current loads, the brass rod is extended by 2 mm. 600 mm B 800 mm P = 2 kN Figure 3

A horizontal cantilever beam, made of steel, is pin-jointed with a vertical brass rod at the end B, as shown in Figure 3. The end C of the rod is pin- jointed to the upper wall. A uniformly distributed load w and a point load P are applied on the beam and rod, as shown. The second moment of area of the beam / = 2 x 106 mm4 and the Young's modulus of steel Esteel = 210 GPa. The brass rod has diameter 5 mm and the Young's modulus of brass Eprass = 110 GPa. Under the current loads, the brass rod is extended by 2 mm. 600 mm B 800 mm P = 2 kN Figure 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
#3A. The rigid bar AB, attached to two vertical rods as shown, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa 3.5 m P B Steel L = 4 m A = 300 mm² E = 200 GPa 2.5 m #3B. A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If the allowable stress is not to exceed 130 MPa at -20°C, what is the minimum diameter of the rod? Assume a=11.7µm/(m °C) and E=200 GPa. C
0.12 For the portal frame shown in the given figure, the shear equation is 4 m P B 4 m El = Constant 4 m To
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D
If the beam is subjected to an internal moment of M=30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. V Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm 150 mm M 15 mm
3. The beam ABCD is fixed with simple support of B and C as shown in the figure below. When point A is 15 mm and point D is bent upward by 10 mm, find the loads P, Q to make point A and D equal to point B and C support points. P is acting on point A, and Q is acting on point D. The Flexible Rigidity tee is 2.5 X 106 Nm (Use Maucalay's method) 15 mm B -2.5 m تے 5m 25m 25m 10 mm
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 320mm² and link (2) has a cross-sectional area of 480mm². For an applied load of P= 58kN, determine the rigid beam deflection at point B. (2) 4,000 mm (1) 2,500 mm B 1,400 mm 800 mm
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. If the temperature is dropped to -40°F and the 20-kip load is then applied, determine the stress in each steel rod at A and C. Use E = 29x106 psi and x = 6.5 x 10-6n for steel. A = 0.5 in.2 3 ft | 20 kips 4 ft - 4 ft 2 ft 2 ft A = 0.75 in.
In the figure it is holding the BCD rod, the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to the BCD rod at point D. C pin is single acting and its diameter is 10 mm. According to this; Find the shear stress at the pin and the bedding stress on the AC rod.
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D C al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E 1/1
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2