A full-wave bridge-rectifier circuit with a 110 O load operates from a 16 V (peak-to peak) 50-H2 supply. For a1050 uf smoothing capacitor, calulate the ripple amplitude. Use the constant-voltage-drop diode model with VD 0.6 V. Select one: O a. 0.64 V O b. 1.18 V O. None of these. O d. 1.28 V O e 0.59 V

A full-wave bridge-rectifier circuit with a 110 O load operates from a 16 V (peak-to peak) 50-H2 supply. For a1050 uf smoothing capacitor, calulate the ripple amplitude. Use the constant-voltage-drop diode model with VD 0.6 V. Select one: O a. 0.64 V O b. 1.18 V O. None of these. O d. 1.28 V O e 0.59 V

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Q4. Determine the value of collector current and collector-to- emitter voltage for the voltage divider bias circuit Shown in Fig.2, .assume B = 100 %3D R, 10 k2 +10 V Rç 1 kO R2 5 kn RE 500 2 ww ww ww
The circuit shown below was used as a current source in a LED lighting application, and voltage quantities shown below were measured for this circuit. What is the maximum number of 1.3V-LEDS that can be connected between Rc and the collector while the transistor still operates as a current source? Ar- L.-.n hu devre icin asağıda - kaynayı uavi ay. diranci ile kollektör arasına 1 3V' m kac tane hašlana ? Measurements: VBE = 0.65 V. VCE = 12 V Re VRc 100 Rb B Q1 10k 2N3904 V2 Re 100 O a. 9 ОБ. 11 O .7 O d. 8 O e. 10
Question continued... Estimate factorial effect of AC? O a. -0.3 O b. 0.3 O c. -0.6 O d. 0.6 Question continued... Calculate the sum of squares for AB (SSAB)? O a. 18.3 O b. 20.3 O c. 22.3 O d. 16.3
A single phase full wave rectifier has two diodes and the forward resistance of each diode is 25 ohms. The transformer secondary voltage from center to each half of the secondary winding is 30 2 V sin wt and the load resistance is 2000 ohms. Compute for the following: A. Average value of load current or the dc load current. B. rms value of load current, C. Peak inverse voltage of each diode
using the transfer function Vo(s)/V:(s) using Simulink and matlab For C=1.4 mF, L= 0.06 H, R1 = 120 2, R2 = 90 2, and v=120 V. The resistors are nonlinear with their saturation limits being +80 V and -60 V. R R
IMPLEMENTATION OF XOR AND XNOR GATES USING NAND GATES 1. Material Required: Logic Trainer Connecting Wires Components(IC’s): 40112. Procedure:It is clear from the logic diagram that the NAND gate implementation of XOR gate requiresfive NAND gates. You will need two quad- 2 in NAND gate ICs to perform this experiment.Gets the required number of ICs containing NAND gates and other apparatus from the labattendant. Plug in the ICs in the breadboard of the Logic Trainer. Connect 5Vdc power supplyand ground on pins 14 and 7 respectively. For other pin configuration consult the data sheet (wehave already used NAND gates in the first lab so it should not be a problem). Wire your circuitaccording to the logic diagram for XOR gate as given above. Once you have wired the circuit,check it with your instructor and, if approved, power up your circuit. The outputs should beconnected to the LEDs on the Logic Trainer for monitoring purpose. Apply different inputcombinations at the input and note…
Operating point represents.…... A. Values of Vce and Iç when signal is applied B. The magnitude of signal C. Zero signal values of Vce and Ic D. None of the above C D В A CLEAD MY CHOICE
A docs.google.com/forms/d/e. Marks 8 The temperature term isn't a part of the .total current density in a semiconductor True False The random motion of holes and free electrons due to thermal agitation is called .drift True False Under the equilibrium conditions, the number of holes which are thermally generated is equal to the holes lost by .recombination True False II >
An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5002. if the forward resistance of diode is 10Q find: i- Peak current through diode. ii- Peak output voltage. iii- What will be these values if the diode is assumed to be ideal (Vdiode =0)?
.9:0A Asiacell Q1.jpg Find the current through the diode in the circuit shown. Assume the diode to be ideal. 50 Ω A R1 V = 10 V 50 R2 B A
В. For the given rectifier output voltage, find the average value of each voltage. Hint: write the answer in the provided box next to the waveform 4 V Figure 12 30V OV -15 V
A simple DC circuit experiment is conducted using a circuit diagram shown below: 26 v 3 mA R R (Indiabix technologies, 2021) In the figure above, two same unknown standard resistor R is connected in the circuit . The voltmeter and ammeter are connected to the circuit as shown above. a) Calculate the unknown resistance of the resistor used in the circuit. b) If we increase the voltage to 40 V, calculate the current measured by the ammeter. | c) Using the data from the above experiment, a graph is plotted between voltage along the Y axis and current along the X axis as shown below: