A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in diameter, and five 12-mm diameter bolts on a concentric bolt circle 250 mm in diameter, Calculate the torque that can be applied if the allowable shearing stress in the bolt is 60 MPa.(detailed solution w/fbd)

A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in diameter, and five 12-mm diameter bolts on a concentric bolt circle 250 mm in diameter, Calculate the torque that can be applied if the allowable shearing stress in the bolt is 60 MPa.(detailed solution w/fbd)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d = 4.0 mm. If the resisting torque supplied by the table leg is equal to 0.3 N · m, what is the maximum shear stress in the drill bit? If the allowable shear stress in the drill bit is 32 MPa, what is the maximum resisting torque before the drill binds up? If the shear modulus of elasticity of the steel is G = 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in diameter, and six 10 mm diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts?
.A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300mm in diameter, and four 19 – mm aluminum bolts on a concentric bolt circle 200 mm in diameter.What torque can be applied without exceeding 62 MPa in the steel or 42 MPa in the aluminum?Assume Gst = 82.7 GPa and Gal = 27.6 GPa.
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt circle. What diameter of bolt should be used if the power transmitted is 26.5 kW and the design shearing stress of the bolt is 12 MPa?
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in lb-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?