J:49) A distribution zone substation has a fault level of 400 MVA on the 11 kV bus. A 2MVAR capacitor bank is used for reactive power support and is switchedtimes of the day. Calculate the frequency in Hz, of the transient generated duringswitching, assuming a nominal power system frequency of 50 Hz.certain

Given data, The value of system voltage is Vs = 11 kV. The value of capacitor bank is C = 2 MVAr.…

A distribution zone substation has a fault level of 400 MVA on the 11 kV bus. A 2 MVAR capacitor bank is used for reactive power support and is switched at certain times of the day. Calculate the frequency in Hz, of the transient generated during switching, assuming a nominal power system frequency of 50 Hz.

A distribution zone substation has a fault level of 400 MVA on the 11 kV bus. A 2 MVAR capacitor bank is used for reactive power support and is switched at certain times of the day. Calculate the frequency in Hz, of the transient generated during switching, assuming a nominal power system frequency of 50 Hz.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.35P: Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are...

See similar textbooks

Similar questions

Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits
Describe the concept of power system harmonics and their impact on the quality of electrical supply.
What is the difference between OLTC and transformers
A 12 MVA, 132/6.6 kV, transformer having a reactance of 0.15 pu is fed from an infinite bus. The transformer feeds two motor each 6 MVA, 6.6 kV. Each motors has a transient reactance of 0.14 pu and a subtransient reactance of 0.30 pu based on its own rating. A three phase balanced fault occurs at the terminals of one motor as shown in the figure below. Find the subtransient fault current and subtransient current in breaker. M1) 132/6.6 KV СВ 38 CB Infinite Bus M2 Fault
A 60 Hz, 33 kV, 3-phase alternator with earthed neutral has a reactance of 7 ohms per phase and is connected to a bus-bar through a circuit breaker. The distributed capacitance upto circuit breaker between phase and neutral in 0.03 uF. Determine (i) peak re-striking voltage across the contacts of the breaker (ii) frequency of oscillations
The bus bars of a power station are in two sections A and Bseparated by a reactor. Connected in section A are two 12MVA generators of 15% reactance each and to B, 8 MVAgenerator of reactance 10%. The reactor is rated 8 MVA and15% reactance. Two feeders are connected to bus bar Athrough transformers, each rated at 4 MVA and 5% reactance.Determine the maximum short circuit MVA with which circuitbreakers on the outgoing side of the transformers have todeal.
"As per the standards used in power system, even harmonics are limited to 25 percent of the odd harmonic limits" True False
Describe the effects of harmonics on power distribution system.
The reactance of the synchronous generator after sometime of the fault cleared is ............
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Circuit breaker usually operate under A) after D. C. component has ceased B) transient state of short-circuit current C) sub-transient state of short-circuit current D) steady state of short-circuit current