Q1:a) Design the oscillator in Figure1 to start oscillation withRclosed-loop gain of 8.5, thensustain oscillation at a resonantR1o VoutfrequencyAssumingof3.4 kHz.the drain-sourceIN914resistance of JFET is 600 N.2N5458b) What will be the feedbackR2C2resistancesettingwhenR3R4C3oscillation is stable?1.0 kNFigure1

Answered: Image /qna-images/answer/fc2e76a9-58ad-4e86-989e-e707f692d998.jpg

a) Design the oscillator in Figure 1 to start oscillation with Ry closed-loop gain of 8.5, then R1 sustain oscillation at a resonant o Vout frequency of 3.4 kHz. Assuming the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback setting R2 C2 resistance when R3 1.0 kfN C3 oscillation is stable? Figure1

a) Design the oscillator in Figure 1 to start oscillation with Ry closed-loop gain of 8.5, then R1 sustain oscillation at a resonant o Vout frequency of 3.4 kHz. Assuming the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback setting R2 C2 resistance when R3 1.0 kfN C3 oscillation is stable? Figure1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
Using any number of Op-Amps, design multistage amplifier to amplify input Ac signal with 0.01V amplitude, the expected output voltage would have 4V amplitude. The input signal frequency = 10 KHz. Assume gain bandwidth product of Op-Amp = 1 MHz
Suppose a small AC voltage of amplitude .1Vpp is added to the input voltage of 5V What is the output AC voltage and the small signal voltage gain? Vin Lo VDD=10V R=10 Q2 Vout
c) As given in the figure a clamper circuit with the input signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic VO versus Vi.
2. b) (i) Derive an expression for the differentiator using op-amp. (ii) Design a circuit to perform differentiation of an input signal that varies in frequency from 20HZ to about 2 KHz. (iii) If a sine wave of 0.5 V peak at 2 KHz is applied to the differentiator of part (ii), draw the output waveform.
Q2// Answer the following questions about voltage-feedback bias circuit for the figure below. 1-Determine Ver and VCB. 2- What happens to the voltage Ve if the resistor Rp is open? 22 K 3- What might cause VCE to become nearly 9 V? 4- Determine the change in Ie from 25° to 75° C, if Ico 0.2 HA, and VBE = 0.7V. 10 ul B-80
A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground
write forward paths and feedback paths.
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
3I Calculate the the Output Voltage of a non-inverting op-amp with the following parameters Rf = 360KOhms, Vo = -9.3V, and Vi = -0.3V. a.31.2 kOhms b.32 kOhms c.12 kOhms d.31 kOHms