A- Design a two-stage BJT amplifier as shown in the figure with coupling capacitors such that the 3 dB low frequencies associated with each stage are equal to 20 Hz. The transistor parameters are: ß = 200 and r7 =5.21KN. %3D Vcc=5 V RCi = 3.5 k2 Rc2 SR1 = 355 kM R = 355 k2 th Cc2 R, = REI = SR2 = зі ко CRE2= ww

A- Design a two-stage BJT amplifier as shown in the figure with coupling capacitors such that the 3 dB low frequencies associated with each stage are equal to 20 Hz. The transistor parameters are: ß = 200 and r7 =5.21KN. %3D Vcc=5 V RCi = 3.5 k2 Rc2 SR1 = 355 kM R = 355 k2 th Cc2 R, = REI = SR2 = зі ко CRE2= ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

what is the Ad gain for the following diferrential amplifier (see attached figure).
If the amplifier in Figure 4 operates with Rsig= 10 kQ and a load of RL=2kQ. Draw the re model alternating current (ac) equivalent circuit of the amplifier. Determine the input and output impedances. Determine the voltage gain Vo/Vin and Vo/Vsig. Calculate the current gain Io/Ii.
Q2) for the amplifier shown in Figure 1) Determine the voltage gain (Av) and the current Gain (Ai) 2) Determine The input and output resistance 3) Determine The output voltage Vout 4) Draw The Ac load line 5) Draw the AC equivalent circuit 6) Determine the maximum input voltage (Vi(p-p)) for maximum output voltage (Vo(p-p)) without distortion. HH Vi-20 mv RB 56 kQ +₁ D B = 50 - 10 V HH RE 1kQ Vou RL • 10 Ω ww11
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
In the self-biased FET amplifier in the figure, Vdd=20V Rs=1kohm Vgsq=-2.6V IDq=2.6mA. It has values of Idss=8mA, Vp=-6V gos=25mikroS. 12mV a.c. to transistor input. What should be the Rd resistance value so that the output voltage is -24.85mV when voltage is applied? answer: 3.3kohm, 3.6kohm, 4.5kohm, 3.9kohm, 4.2kohm is one of the answers.
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
Calculate the common-mode gain for the amplifier circuit below. Refer to the image for the circuit configuration, but refer to the following for the values: Vcc = 10 V, Rc = 74674 ohms, RE = 70254 ohms, -Vcc = -11 V, Vi1 = 0 V, ri1=ri2= 29354 ohms, beta1=beta2 = 75.
Draw the DC and AC load line for a transistor amplifier circuit shown in Figure, also describe the optimum operating Point for the given values as follows: Rc = 10 KQ ; RL=20 KQ and V cc = 20 V +Vcc Ic Rc Cc Cc V. out R1 Vin www
Draw and design an operational amplifier circuit that has an input V₁, output Vo, and transfer characteristic as shown in figure (4). 1.5 a Volv Figure (4) 0.5 -vi/v
3I Calculate the the Output Voltage of a non-inverting op-amp with the following parameters Rf = 360KOhms, Vo = -9.3V, and Vi = -0.3V. a.31.2 kOhms b.32 kOhms c.12 kOhms d.31 kOHms
The transistor parameters for the circuit in Figure are B1 =B2 = 100, VBE1(on) = VBE2(on) = 0.7 V, and VA1 = VA2 %3D =00.Find the small signal voltage gain Av = vo/vs. (Note that VT=0.026 V) %3D Vcc=9 V Rib Q2 1 ko -R. 20 V 100 Q -14.76 O 0.899 -55.3 ww ww
C. A variable capacitor. O d. An amplifier. When operating in the saturation region, the current gain 'B' of the bipolar transistor increases Select one: OTrue O False Assume Is= 8x 105 A, B-100, and VA =-. For the circuit shown below and for -0.5 mA, the value of the transconduce Vcc=2 V Q1