A cylindrical vessel 3m high and 1.50 m diameter is filled with water to a depth of 2.50m. In its side is a 50mm circular orifice C=0.60 placed 30 cm above the bottom of the vessel. If the vessel be rotated about its own axis at 60 rpm and the water is allowed to escape through the orifice for a period of 3 minutes, compute the a. Difference in elevation of the water surface at the center and at the periphery of the tank at this instant.

A cylindrical vessel 3m high and 1.50 m diameter is filled with water to a depth of 2.50m. In its side is a 50mm circular orifice C=0.60 placed 30 cm above the bottom of the vessel. If the vessel be rotated about its own axis at 60 rpm and the water is allowed to escape through the orifice for a period of 3 minutes, compute the a. Difference in elevation of the water surface at the center and at the periphery of the tank at this instant.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.76P: A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area...

See similar textbooks

Similar questions

Please indicate the given, the required and the illustration. An open cylindrical vessel, 3m high and 1.5m in diameter is filled with water to a depth 2.5m. In its side is a 50mm circular orifice C = 0.60 placed 300mm above the bottom of the vessel. The vessel is rotated about its own axis at 60rpm and the water allowed to escape through the orifice for a period of 3 minutes. Determine the volume (V) of water allowed to escape through the orifice in cubic meters. Answer is 1.440
A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter 400 mm at the bottom. Find the time taken by water : (a) to fall from 4 m to 2 m. (b) for completely emptying the tank Take Cd= 0.6
... K 3m 3.5m Im 100mmg An open tank in the form of frustum of a cone has 1m diameter at the bottom and 3m at the top as shown. It is 3.5m high and filled with water at the top. A 100mm diameter orifice with C = 0.92 is located at the bottom of the tank. Determine the time to empty the tank
A water tank is filled with water to a height of 4.3m above the 10mm diameter orifice which is connected at the side of the tank. How far would the water have traveled horizontally if the orifice is 4.3m above the ground.
Find the surface tension of the water jet of 38 mm diameter when the inside pressure is 4.5 N/m2 The surface tension in N/m is
Describe the forces that enable the submarine to descend or ascend in the seawater. When the submarine holds at the constant depth of 3,500m, calculate the buoyant force on the submarine. weight of seawater in the ballast tank. seawater pressure. When seawater flows into the bottom opening at 10 m/s, calculate the velocity of the seawater level (8m above the bottom of the submarine) inside the ballast tank (v on diagram). Calculate the net force on the submarine circular hatch door (10m above the bottom of the submarine) with a radius of 0.5m. The air pressure inside the submarine below the hatch door is 150 101.3 kPa. Calculate the change in heat energy of the submarine’s outer haul, when it descends from the surface to a depth of 3,500m (with an average temperature of 20°C). Calculate the power of the submarine’s electrical heater needed, to maintain the interior of outer hull at 30°C. The exterior of outer hull is 10°C. (Assume heat of the submarine…
The head lost from point 1 to point 2 is 4m. If the specific gravity of mercury is 13.6, determine The velocity at point 1 in m/s and the maximum height the water can reach “hm” if neglecting air friction in m
A closed tank contain water up to a height of 2 m and over the water surface there is air having a pressure of 90 kPa above atmospheric pressure. Find the discharge through a small sharp-edged orifice of 15 cm dia. at the bottom of tank. Take C=0.6.
A closed vertical cylindrical vessel, 1.80m in diameter, 3m high is 8/10 full of oil (SG=0.85) and revolved about its vertical axis with a constant angular speed. The air inside the vessel is 135 kPa. a. Determine the angular speed in radian per second necessary to set the vertex of the liquid surface 0.60m above the bottom of the vessel. b. What is the maximum pressure at the bottom of the tank during rotation? c. If the angular speed in rev/min is 128.71, determine the diameter of the portion free of liquid at the vessel in cm. d. If the angular speed is 200 rev/min, determine the area of the portion free of liquid at the bottom of the vessel.
17 An open circular cylindrical pipe of radius R and height h is completely filled with water with its axis vertical and is rotated about its axis at an angular velocity w. Determine the value of w in terms of R and h such that the diameter of the exposed center portion is equal to the radius of the cylinder. Cind ah
If the rate of rotational speed of the 3-tube system shown is ? = 10 rad/s, determine the water heights in each tube leg. At what rotational speed will the middle tube be completely empty?
Jet of liquid (14 mm diameter) ejections vertically into the atmosphere. The pressure inside the jet (due to surface tension) will be slightly higher than the atmospheric pressure. Determine the difference in pressure (in Pascal). (take o = 8.35*10-2 N/m for liquid)