A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 259

A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 259

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asap
Problem 1: A cylindrical pressure vessel with an inner radius of 1.25 m and a wall thickness of 21 mm is subjected to an internal pressure of 8 MPa. Find the normal stress and shear stress along the 45° weld seam. 45° -1.25 m
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
For the closed tank as shown below, is subjected to a internal pressure of 1.5 Mpa, and tensile force of 2000 kN. diameter 500mm thickness 12 mm. 72. Calculate the normal stress on 450 weld. Calculate the in-plane shear stress on 450 weld.
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Lütfen birini seçin: a. 9.3175 MPa/6.09 MPa b. None c. 0.417 MPa/4.38 MPa d. 0.6256 MPa/6.70 MPa e. 11.874 MPa/6.70 MPa
A cylindrical pressure vessel 4 ft in diameter is welded using a spiral seam that makes an angle of 30° with respect to a transverse plane of the cylinder, as shown below. For an internal pressure of 180 psi and a wall thickness of 3 in, determine (a) the normal stress perpendicular to the weld, and (b) the shearing stress parallel to the weld. 30%
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl
The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams at an orientation of Assume B = 62.5. The tank has an inside diameter of d- 1800 mm and a wall thickness of t-7 mm. For a gage pressure of p-0.8 MPa, determine (a) the normal stress perpendicular to the weld and (b) the shear stress parallel to the weld. (a) on MPa (b) Tnt" MPa
Q2 seams that form a B= 30° angle with the transverse plane. For a gauge pressure of 0.5 MPa. . You see the pressure tank in Figure 2. It has a wall thickness of 6 mm and butt-welded (a) Please find the normal stress perpendicular to the weld, (b) Please find the shearing stress parallel to the weld. 5 m 1.8 m Figure 2