A crate of mass 15 kg needs to be moved across a fioor. The coefficient of static friction between the floor and the crate 0.25. A distributed load of 15 N/m acts on the top of the crate. Determine the smallest force Papplied as shown which will cause the crate to move. Note that you must check for both slipping and 3. tipping of the crate. 15 N/m 30 P. 1.8m 12 m 0.8 m

A crate of mass 15 kg needs to be moved across a fioor. The coefficient of static friction between the floor and the crate 0.25. A distributed load of 15 N/m acts on the top of the crate. Determine the smallest force Papplied as shown which will cause the crate to move. Note that you must check for both slipping and 3. tipping of the crate. 15 N/m 30 P. 1.8m 12 m 0.8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5-4.6. The 500-lb block shown in Fig. P-5-4.6 is in contact with a 45° incline. The coefficient of static friction is (0.25. Compute the value of the horizontal force P necessary to (a) just start the block up the incline or (b) just prevent motion down the incline. (c) If P = 400 lb, what is the amount and direction of the friction force? %3D
A packing crate of mass 40 kg is pulled by a rope as shown. The coefficient of static friction between the crate and the floor is 0.35. If a = 40°, determine (a) the magnitude of the force P required for impending motion of the crate and (b) whether sliding or tipping is impending. A 0.5 m C P af o -0.8 m B D
F8-3. Determine the maximum force P that can be applied without causing the two 50-kg crates to move. The coefficient of static friction between each crate and the ground is pe = 0.25.
A cast-iron beam 10-m long and supported, carries a uniformly distributed load of intensity W. (including its own weight). If the inverted T will be put into its upright position (now it will be T-Section Cast-iron Beam) and the allowable stresses are fit s 20 MPa and fbe 5 80 MPa. Determine the maximum safe value of w. (kN/m) if x = 1.0 m. 10 m 180 mm We N.A. 50 mm R. Ra INA = 36 x 106 mm
Please Quickk. In a high rise building, the elevator rises 366 m with an operating speed of 5 meters per second and reaches full speed in 10.68 m. The loaded elevator weighs 2000 kg. The acceleration of the elevator in m/s2 is 1.17. Determine the bending stress of wire rope with drum diameter of 7.8 inches and wire diameter of 0.0987 in. Answer 380 ksi
Determine the maximum force P that can be applied without causing movement of the 250-lb crate that has a center of gravity at G. The coefficient of static friction at the floor is μs = 0.4.
The 11-lb block has a velocity of 3.83 ft/s when the force of F= (257.6t) Ib-ft/sec2 is applied. Determine the acceleration of the block whent= 2.08 s. The coefficient of kinetic friction at the surface is u 0.21. Answer is in ft/sec. F = (257.6P) Ib ft/sec? ty
Friction Problem 350kN A 350 kN block is resting on a rough horizontal surface for which the coefficient of friction is 0.45. Determine the force P required to cause motion to impend if applied to the block. A. Horizontally B. Downward at 30' with the horizontal. F N C. What minimum force is required to start motion?
1. Determine the maximum force P needed for the homogenous block to be in static equilibrium. What will happen to the block if the magnitude of force P went above the maximum? The coefficient of static friction between the block and the floor is 0.30. The weight of the block is 500 lb, indicate the direction of the impending motion. 40° Guide Questions: a. What is the direction of frictional force on the 500 lb block? b. If slipping is impending, can we assume that F = μ,N? c. Where is the location of the frictional force on the block if tipping is impending? Answer: Pmax=432.55 lb The block will tip to the right before it slips. 4 ft 6 ft
QUESTION The figure shows an idealized two-cell symmetric wing box structure. Dimensions of the wine box are 12 in x 5 in. All boom areas and panel thicknesses are given on the figure. If all panels of the wing box are made of the same material, and the following loads are applied: A vertical shear Sy = 1,500 Ib along the middle vertical web, and a torque T= 750 lb.in (clockwise). Calculate the maximum shear flow in the wing box. %3D Solution: 1 in.? 0.3" 0.5 in.2 0.3" 0.5 in.? 0.5" 0.5" 0.5" 1 in.? 0.3" 0.5 in.2 0.3" 0.5 in.2
Problem 1 W MB A B * 4 m 2 m The cantilever beam above is made up of concrete with E- 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS SET b (mm) 300 h (mm) w (kN/m) Mb (kN-m) 500 20 40 Using area moment method, determine the following: 2. Moment reaction at A, MA. 2°
CHAPTER 4: *FROM ....TL F 2014 The load is 80 kN supported by the four 304 stess steel wires that are connected to the rigid members AB and DC. Determine the vertical displacement of the load if the members were horizontal before the load was applied. Each 4m H C {E= 18.7 Gpa } wire has a cross-sectional area of (50 mm'. Sm 5 kN 4.5m *Delerm