A constant head hydraulic conductivity test is performed on a sample from anaquifer. Determine the horizontal hydraulic conductivity for the following specimen in units of [cm/s].The length, L, of the specimen is 25cm and the diameter of the specimen is 7.5cm. The specimen issubjected to a head, e, of 0.2m. In 5 minutes of steady flow, 20ml of water exited the specimen. Specifythe most likely type of geologic material the specimen is based on the hydraulic conductivity value.

A sand sample of 35m cm^2 cross sectional area and 20cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6min. The dry weight of sand used for the test was 1120 g, and Gs= 2.68 A. Determine the hydraulic conductivity in cm/sec. B.Determine the discharge velocity in cm/sec. C. Determine the seepage velocity in cm/sec.

P 4: A sand sample of 35cm2 cross sectional area and 20cm long was tested in a constant head permeameter. Under a head of 60cm, the discharge was 120ml in 6min. The dry weight of sand used for the test was 1120g, and G3=2.68. Determine (a) the hydraulic conductivity in cm/s, (b) the discharge velocity, and (c) the seepage velocity. Answers: a) 3.174 x 103 cm/s, b) 9.52 x 10³ cm/s, c) 2.36 x 10-² cm/s

A constant head test is performed using a permeameter in the laboratory. The graduated cylinder collects 892 cm3 of water in 112 seconds. The soil specimen diameter = 18 cm , th elevation of water in upper-most piezometer is 181 com , the elevation of water in lowest piezometer is 116.6 cm and the piezometer inlets are evenly spaced at 16.7 cm on center. Compute the hydraulic conductivity, k and choose the correct answer below based on that. O A. 2.1 x 10^-3 cm/second O B. 1.5 x 10^-2 cm/second O C. 2.91 x 10^-2 cm/second O D. 2 x 10^-2 cm/second QUESTION 10 Given: -Applied stress on a soil = 122 kPa %3D -Influence Factor = 0.4 Compute the change in stress at 10 m below the edge of 25 m dimeter oil tank and select the correct answer from below: O A. Change in stress = 44 kPa O B. Change in stress = 49 kPa O C. Change in stress = 40 kPa O D. Change in stress = 42 kPa %3D

1. A sand sample of 35 cm² cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 mL in 6 min. The dry weight of sand used for the test was 1120 g, and G₁ = 2.68. Determine (a) the hydraulic conductivity in cm/sec, (b) the discharge velocity, and (c) the seepage velocity.

A constant-head permeability test is performed where the hydraulic gradient is 0.75. The crosssectional area of the sample is 0.25 ft2. The quantity of water flowing through the sample is measured to be 0.004 ft3/minute. (a) What is the coefficient of permeability in feet per minute? (b) What is the coefficient of permeability in millimeters per second?

Problem 3. A sand sample of 35 cm2 cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6 min. The dry weight of sand used for the test was 1 120 g, and Gs = 2.68. Determine (a) the hydraulic conductivity in cm/sec, (b) the discharge velocity, and (c) the seepage velocity.

For a falling head permeability test, these valueare given: Length of the soil specimen = 200 mm Area of the soil specimen = 1000 mm2 Area of the standpipe = 40 mm2 Head difference at time, t = 0 min is 500 mm Head difference at time, t = 3 min is 300 mm1. Determine the hydraulic conductivity of thesoil in cm/sec.2. What was the head difference at time, t =100 sec?

A pumping test was carried out in confined aquifer thickness 2 m and the following measurement was recorded. Rate of pumping was 10 m^3/s; drawdown in pumping well was 2.0 m while on the observation well located at 15 m and 20 m from the centre of the pumping well were 1.6 m and 1.4 m, respectively. Determine the hydraulic conductivity of soil.

Determine the following: a) hydraulic conductivity is ______ x10^3 cm/sec b) Transmissbility of the impermeable layer is _____ cm^2/sec c) The drawdown in the test well is ____ m