Answered: A compound channel in FIGURE Q2(b) has…

A compound channel in FIGURE Q2(b) has bottom slope of 0.6-percent. Calculate velocity and discharge of the channel if Kutter coefficient n is 0.042. www ww

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.11P

See similar textbooks

Related questions

Q: Design a trapezoidal open channel of most efficient section with one side slope (V:H) and the other…

Q: You are given the following information about a triangular channel: Top width, B = 3 m Q = 7.23…

A: Given data: Top width of the channel (B) = 3 m Flow (Q) = 7.23 m3/s (manning’s constant) n = 0.016

Q: 4. A trapezoidal channel with 3 meters bottom width, side slope 2H:1V, channel gradient of 0.002,…

Q: A 4 m wide rectangular channel, having bed slope of 0.001 carries a discharge of 16 16 m³/s.…

A: Given data in question Bed slope Discharge Constant Width To find out Category of channel

Q: (b) A channel is to be designed for carrying a discharge of 50 m³/s, side slope 0.5:1 and silt…

Q: a rectangular channel 4.8m wide carries water at the depth of 0.75m and a mean velocity of 0.85 m/s.…

A: The width of the channel is b=4.8 m. The depth of water is y=0.75 m. The velocity is V=0.85 m/s. The…

Q: Find the base width and water depth of a trapezoidal channel with side slopes of 1.5 horizontal to 1…

Q: QUESTION 3 3.1. A trapezoidal channel convey 15 m³/s of water on a bed slope of 1 in 200. The base…

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly…

Q: c) A rectangular concrete channel has a broad crested weir at its downstream end similar to that in…

A: The expression of velocity is given as V1=1nR23S12 V1=1nbynb+2yn23S12 Here n is the manning…

Q: Estimate the lag time (hr) for the following watershed: Hydraulic length (km) - 3.04 Curve number 60…

A: Given data:Hydraulic length(L)=3.04 km=9973.753 ft.Curve number(CN)=60 Average land slope(S)=1.1%

Q: Determine the critical depth in meters for rectangular channel. Base width = 9m Discharge = 180…

Q: section

A: Discharge Q = 2.0 m³/s Roughness Coefficient n = 0.030 Longitudinal Slope S = 0.05 To determine -…

Q: The trapezoidal channel below must supply a discharge rate of 42 (m3/s). The Manning’s roughness of…

Q: 1. An unsymmetrical trapezoidal channel with one side vertical and the other inclined from…

Q: Question 5. Design a rigid boundary earth channel to carry a discharge of 1.08 m³ per second. Given…

Q: Water Resources Engineering: Open Channel Flow Determine the cross section (i.e. find the slope,…

A: The trapezoidal section is shown below:

Q: A trapezoidal channel 5 m wide and having side slopes of 1.5 horizontal: 1 vertical is laid on a…

A: The Manning's formula is given by: Q=1ηAR23S12 Where, Q = Discharge A = Area of trapezoid R =…

Q: A surface drainage trapezoidal channel has to be designed for a drainage area of 500 ha. The…

A: Hello dear Please find the attached solution below, thanks

Q: Design an irrigation channel by Kennedy’s theory to carry 5 cumecs of discharge with critical…

Q: Water in a rectangular channel flows into a gradual contraction section as indicated below. If the…

Q: Determine the bed slope of a rectangular channel 5 m wide and 2 m deep. The discharge is recorded as…

A: Given: Width of channel, b = 5 m Depth of channel, d = 2 m Discharge, Q = 20 m3/s Chezy's constant,…

Q: c) The channel shown in Figure 1 below is laid at a slope of 0.0018 and has a Manning's roughness of…

A: Given: Slope (s) = 0.0018 Manning roughness co-efficient (n) = 0.015 Normal depth of flow = 2.11m…

Q: Hydraulic mean depth of a rectangular channel having Width as 2 m and flow depth 50 cm 0.333 0.222

A: H=Wetted AreaWetted PerimeterWetted Area=2m×0.5m=1m2Wetted Perimeter=0.5×2+2=3m

Q: Determine the balancing depth (y) for a canal partially in cutting and partially in filling, having…

Q: Problem 4. A trapezoidal channel has a bottom width of 6 m and side slope of 2:1. If the depth of…

A: Given: The bottom width B, is 6 m. The depth of flow y, is 1.2 m. The flow Q, is 20.40 m3/s Side…

Q: Exercise [3] Calculate the depth d in which the discharge (Q=1.5 m³/sec) will flow through the…

Q: The discharge in an open trapezoidal channel was measured by slope area method. Depth of water =…

A: given- a trapezoidal channel carrying water having depth of water=2.5m bottom width of channel=3.10m…

Q: Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is…

A: Depth of the water in channel y= 4.0 mwidth of the base X=85 mSide slope = 2V:1H=1V:0.5H here…

Q: A trapezoidal channel is to be designed to convey a discharge of 50 m³/sec at a velocity of 2 m/sec.…

A: GivenTrapezoidal channel-Discharge Q=50 m3/sVelocity V=2 m/sbed width to depth ratio-By=0.8side…

Q: Find the value of cross sectional area of channel having discahrge value is 20 m3/s and flow…

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: Calculate the hydraulic mean radius Manning's equation for a trapezoidal channel to carry 200 cumec…

Q: Design an irrigation channel by Kennedy method to carry 50 m³/s of discharge with base width to…

Q: A rectangular channel Carrie's water to a depth of 1.8m. In order to measure the discharge, the…

A: Rectangular Channel is an open channel with a rectangular cross section. The flow routing through a…

Q: 6. A 3.6 m wide rectangular channel caries water to a depth of 1.8 m. In order to measure the…

A: To Determine Discharge in the rectangular channel.

Q: Solve for the slope of the bottom of the channel shown below per kilometer length if the discharge…

Q: Calculate the depth d in which the discharge (Q=1.5 m/sec) will flow through the channel with…

Q: 4.a. A trapezoidal channel 5 m wide and having side slopes of 1.5 horizontal: 1 vertical is laid on…

A: Given that: Base width of the channel, B = 5mSide slope: m = 1.5Longitudinal…

Q: Consider the size of trapezoidal drainage channel. • Bed slope of channel= 0.015ft/ft • Depth of…

Q: Determine the Froude number for the flow in a trapezoidal channel with the depth of water as 2 m and…

A: Draw the figure. It is required to determine the area of the channel.

Q: A rectangular channel 6 m wide and 3 m water depth and having a bed slope as 1 in 2000. If Chezy's…

Q: Q1/ Find the Width of channel if it has side slope and bed slope (1:1) and (1 to 1000) and the ratio…

Q: r flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m, the :…

Q: Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is…

A: Given: n=0.012S=11500width=85

Q: 2. Flow occurs through a sand-filled pipe with a cross- sectional area of 60 cm?. If K is 10 cm/s…

Q: Example 3: Design a trapezoidal channel of water having a velocity 0.6 m/s, channel side slope…

Q: The area of a channel section is 8m2 and the wetted perimeter is 8m. if the discharge is 33.33m/s…

A: Area A=8m2 Perimeter P=8m Discharge Q=33.33m3/ n=0.012

Q: A trapezoidal channel having side slopes of 1:1 and bed slope of 1 in 845 is required to carry a…

A: Given: The side slope of the channel is 1:1. The bed slope is 1 in 845. The discharge is the channel…

Q: Design a semi-circular open channel (n=0.014) that is anticipated to convey 20cumecs of water. The…

A: Given data: Q= 20cumecs slope of the channel bed = 0.0015 n=0.014 It is asked to design the…

Q: Design a semi-circular open channel (n=0.014) that is anticipated to convey 25cumecs of water. The…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

A compound channel in FIGURE Q2(b) has bottom slope of 0.6-percent. Calculate
velocity and discharge of the channel if Kutter coefficient n is 0.042.
(b)

0.5 m
1.5 m
1.5 m
'0.5 m'
1.5 m
3 m
Figure Q2(b)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2: Given data

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Direction: Choose A- When both statements are true; B - When both statements are false; C- When the first statement is true and the second statement is false; D- When the first statement is false and the second statement is true. First Statement: The piezometric surface of an aquifer confined by an aquiclude is higher than that of an unconfined. Second Statement: Hydraulic conductivity is a measure of permeability or impermeability of a geologic unit. OA B. D.
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
4. Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is incompressible and flowing at a volumetric flowrate of 0.35 m³ s-¹. The piezometric head is 1 m at the upstream location (1) and 0.5 m at the throat (2). The pipe diameter at the upstream location (1) is 0.5 m. Answer the following: 1 m Flow Streamline- 0.5 m Datum Hint: the piezometric head is the sum of the elevation and pressure heads. (a) Find the velocity in the upstream section. (b) Find the velocity in the throat section. (c) Find the diameter in the throat section. (d) Based on your findings in (a) and (b), qualitatively describe how pressure and velocity are related along the streamline.
At Point A, in a pipeline carrying water (y=62.4 Ib/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2psi.determine the following:(a)quantify the losses in this system and (b) is the flow going from Point A to Point B or from point B to point A. why?
6. The sludge hopper of a sedimentation tank is approximated as a truncated square prism provided with an orifice of 100 mm dia. at its bottom as shown in the figure. The sludge is being discharged through the orifice Determine the time taken for emptying the hopper. Assume Cd=0.62. 2m 1m E im -
1. A 1 meter diameter pipe 1400 m long has a discharge of 600 liters/ sec a. Compute the head loss using f = 0.018 b. Compute the head loss using n = 0.015 c. Compute the head loss using C = 100 %3D %3D %3D
The velocity in this channel is 0.9 m/sec. The Froude number is 6.73 m y=1.5 m 5 m 0.82 .a O 0.25 .b O None of these .c O 0.57.d O
A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the water is following. The pipe is located at 5 metre above the datum line. The sum of total head and stagnation head is m. (g = 10 m/s?). (assume 1 bar = 105 Pa) %3D
(b) Calculate the discharge from a tubewell of 20-cm diameter penetrating fully into a confined aquifer of 20-m thick and having a permeability of 40 m/day. The drawdown in the well is 3 m and zero drawdown at 300 m from the well. If the diameter of the well is doubled, find the percentage increase in the yield, the other conditions remaining the same. State the assumptions in the formula you use. Ans: (1303.7 lpm)
The flow through the aquifer can also be calculated from the equation dh (2.8) Q = -T dx level is
Water backs up behind a concrete dam as shown in the Figure. Leakage under thefoundation gives a pressure distribution under the dam as indicated. If the water depth, h, is toogreat, the dam will topple over about its toe (Point A). The width of the dam is L and the heightof the dam is hd. Specific weight of the concrete is γc, the specific weight of the water is γw.Base your solution on a unit length of the dam. Sketch the free body diagram. Write the solutionprocedure step by step to determine the maximum water depth (h) in order not to cause anyoverturning about point A
Problem: Three pipes of different length and diameters connected in series as shown discharges 160 liters per second. If the roughness coefficient n = 0.012 and disregarding minor losses. Determine the head loss in pipe 2. A (1) B (2) (3) D 450 тто, 180 m 300 тто, 1500 т 250 тто, 800 т