A column was designed with 200UC46.2. The length of the column is 4500 mm and both ends can be assumed as pin ends. Girders are provided at 1500 mm distance in the major axis direction (to provide minor axis buckling restraints). Estimate maximum design load of the column in kN.

A column was designed with 200UC46.2. The length of the column is 4500 mm and both ends can be assumed as pin ends. Girders are provided at 1500 mm distance in the major axis direction (to provide minor axis buckling restraints). Estimate maximum design load of the column in kN.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
b) This is a concrete frame (the interior lines represent reinforcing bars), If P is dead load, draw the BMD and the SFD as a result of ULTIMATE LOAD. 6.0 ft. P= 1.0 Kip Own weight of the beam = 1.0 kip/ft. (Uniform dead load)
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
A 290 N/m light crane rail sits on and is securely fastened to a W400 mm x 67 kg/m crane girder. The girder is simply supported on a span of 9m. Crane wheel loads: V = 80kN, H = 8kN Assume full transfer of lateral load to the top flange of the girder. Girder properties are: A =8580 mm2 d= 400mm tw = 8.5mm bf = 179mm tf =14mm Ix = 2.44 x 108 mm4 Iy = 0.14 x 108 mm4 a) What is the maximum bending stress, fbx (MPa), in the girder? b) What is the maximum bending stress, fby (MPa), in the girder? c) Using the interaction formula, fbx/Fbx + fby/Fby, determine the maximum span of the girder so that the section shall be adequate for the given loads if the allowable stresses are: Fbx = 207 MPa; Fby = 258 MPa.
Each bar of the truss has a rectangular cross section, 30 mm by 60 mm. Determine the maximum vertical load P that can be applied at B if the working stresses are 100 MPa in tension and 80 MPa in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) B 8m Gm 10m
Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beam weight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f'c =4,000 psi. For the beam, Fy = 50 ksi and = 36 ksi for the plate. Use LRFD. If {b = 8 inch and B = 14 inch, what is the minimum computed thickness of the bearing plate in inch? Express your Fy answer in three decimal places.
The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider is symmetrical. The bearing stiffeners at supports are the sole means of providing restraint against torsion. Design the bearing stiffeners at supports. with minimum moment of inertia about the center line of web palte only as the sole design criterion. The flat section available are: 250 x 25, 250 x 32, 200 x 28, and 200 x 32 mm. Draw a sketch 500 25 8 .1445 Dimensions in mm 20 +425
Steel Design Two channels having the given properties shown is placed at a distance of 300 mm to back and is properly connected by a pair of lacings as shown. Properties of one channel A = 5595 mm2 d = 305 mm x = 17mm Ix = 67.3 x 106 mm4 Iy = 2.12 x 106 mm4 rx = 19.3 mm Assume K = 1.0 Determine the safe axial load in kN, that the column section could carry. Unsupported height of column is 6m.
Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beam weight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f’c =4,000 psi. For the beam, Fy = 50 ksi and Fy = 36 ksi for the plate. Use LRFD. If ℓb = 8 inch and B = 14 inch, what is the minimum computed thickness of the bearing plate in inch? Express your answer in three decimal places.
Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beam weight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f'c =4,000 psi. For the beam, Fy = 50 ksi and Fy = 36 ksi for the plate. Use LRFD. What is the minimum bearing length, {, to prevent web yielding in inch? Express your answer in two decimal places.
The given frame is unbraced, and bending is about the x axis of each member. The axial service loads are: DL= 908 KN and LL= 1816 KN. E= 350 MPa. Use LRFD. a). Determine Kx for member AB. Use the stiffness reduction factor if possible. b). Determine the axial compressive design strength of column AB. 7.60 m W18 × 50 Am WI8 x50 B 4m WI8× 97 26X81M
AW460×60 steel beam is loaded as shown. Assume w - 50 kN/m, Mo - 95 kN-m, Las - 3.8 m, Lec - 1.6 m, E- 200 GPa, and I- 255 x 10° mm. (a) Determine the reaction force at roller B. Forces are positive upwards. (b) Determine the maximum positive bending moment in the span. (c) If the allowable bending stress is 210 MPa, determine the minimum acceptable section modulus for the steel beam. Mo LAB LBC Answer: (a) Ву - kN (b) Mpos kN-m (c) Smin x 10° m3