A coil wound 3000 turns in the form of an air-cored torus with a square cross section. The inner diameter of the torus is 60mm and the outer diameter is 100mm. The coil current is 0.3A. (a) Determine the maximum and minimum values of the magnetic field intensity within the roidal coil. (b) Determine the magnetic flux within the torus. (c) Determine the average flux density across the torus and compare it with the flux density idway between the inner and outer edges of the coil.

A coil wound 3000 turns in the form of an air-cored torus with a square cross section. The inner diameter of the torus is 60mm and the outer diameter is 100mm. The coil current is 0.3A. (a) Determine the maximum and minimum values of the magnetic field intensity within the roidal coil. (b) Determine the magnetic flux within the torus. (c) Determine the average flux density across the torus and compare it with the flux density idway between the inner and outer edges of the coil.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ferromagnetic core in the shape of a doughnut has a cross-sectional area of 0.11 m2 and an average length of 1.4 m. The permeabil ity of the core is 1.206 × 10-3 Wb/A-t. m. Determine the reluctance of the magnetic circuit
A coil that con sists of 450 windings is wound aroundabakelite ring. The mean diameter of the ring is 100 mm and the diameter of the bakelite core is 20 mm. The currentthrough the coil is 3 A. Determine: 1.1 a) the field stren gth b) the flux den sity c) the total flux A ringhas two halves. The onehalf is made from Cast iron, while the other is made from Cast steel. The two halves are held 1 mm apart with the aid of a paper disc. The cross-section al area and mean circumference of the ringis 345 mm? and0.6 m respectively. Therelative permeability of cast iron is 2400, while that of cast steel is 600. The ring has a coil with 200 win dings. The currentflow through the coil causes a flux den sity of 0.48T. 1.2 Calculate the: a) mmi b) currentflow Ignore the effects of fringing andleakage.
A magnetic circuit has a length of 100 cm and cross-sectional area of 5 square cm. The total flux is 10 x 104 webers. The coil has 100 turns and current of 4 amperes. What is the magnetic strength? a. 500 AT/m b. 400 AT/m c. 350 AT/m d. 450 AT/m
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
A coil that consists of 450 windings is wound around a bakelite ring. The mean diameter of the ring is 100 mm and the diameter of the bakelite core is 20 mm. The current through the coil is 3 A. Determine: a) the field strength b) the flux density c) the total flux
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
B. For the following magnetic circuit, the flux passing through the core is 1.32 mWb, the cross section of the core is 3 cm by 4 cm, the laminated section has a stacking factor of 0.9, and the gap is 1 mm. Determine the flux density in each section. Neglect fringing d N turns Cast iron Air gap Laminated sheet steel
The physical construction of two pairs of magnetically coupled coils is shown. Assume that the magnetic flux is confined to the core material in each structure. Show two possible locations for the dot markings on each pair of coils.
15. A toroidal core with a mean circumference of 100 cm and a cross sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800.
1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. -10 cm- - 20 cm- 15 cm 400 turns 15 cm 15 cm Core depth 5 cm