A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: Peak to peak ripple voltage RMŞ ripple voltage 4. а.

A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: Peak to peak ripple voltage RMŞ ripple voltage 4. а.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
LR phase shift control is used in a controlled rectifier. If the value of the inductor is 100 mH, find the minimum and maximum value of the control resistor if the ratio of Idc/Idcmax is to be 0.1 to 0.9.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A full wave bridge rectifier is supplied from 230V, 50Hz and uses a transformer of turns ration 15:1. It uses load resistance of 50 ohms. Calculate load voltage and ripple voltage. Assume ideal diode and transformer. Assume ripple factor equals to 0.482. a.Load Voltage= 13.8 V; Ripple Voltage=6.652 V b.Load Voltage= 15.6 V; Ripple Voltage=7.611 V c.Load Voltage= 21.3 V; Ripple Voltage=8.410 V d.Load Voltage= 25.1 V; Ripple Voltage=10.442 V
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current