A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its

A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
Three capacitors 6, 10 and 15 uF are connected in series across a 100 volt supply. Find the voltageacross the 10uF capacitor.
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
I am getting the output of the clamper circuit wrong, how will this circuit be output ? circuit question : Set the input voltage signal to a sinusoid with 100 Hz frequency and 20V peak-to-peak amplitude with C=1μF. Obtain and plot the input and output voltage waveforms.
An inductor and a resistor are in series with a sinewave voltage source. The frequency is set so that the inductive reactance is equal to the resistance. If the frequency is increased, then options: Voltage across the inductor= Source Voltage Voltage across the inductor> Voltage across the resistor Voltage across the inductor= Voltage across the resistor Voltage across the resistor > Voltage across the inductor
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
A capacitor C is connected in parallel with a resistor R across a 120 V, 200 Hz supply. The supply current is 2 A at a power factor of 0.6 leading. Determine the values of C and R.
A resistor of 20ohms and a capacitance of unknown value when connected. In in parallel across a 100V, 50Hz supply take a current of 6A. The combination is now connected across a 100V supply of unknown frequency and the current falls to 5.5A . What is the frequency?
Q6) The waveform of the voltage obtained after rectification is of a -----nature and therefore contains .harmonics a. Sinusoidal O b. Triangular c. Pulsating O d. Repetitive O