A bird is flying in a room with a velocity field of V-› = (u, ? , w) = 0.6x + 0.2t – 1.4 (m/s). The room is heated by a heat pump so that the temperature distribution at steady state is T (x, y, z) = 400 – 0.4y – 0.6z – 0.2 (5 – x)2 (°C). Calculate the temperature change that the bird feels after 10 seconds of flight, as it flies through x = 1 m.

A bird is flying in a room with a velocity field of V-› = (u, ? , w) = 0.6x + 0.2t – 1.4 (m/s). The room is heated by a heat pump so that the temperature distribution at steady state is T (x, y, z) = 400 – 0.4y – 0.6z – 0.2 (5 – x)2 (°C). Calculate the temperature change that the bird feels after 10 seconds of flight, as it flies through x = 1 m.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.31P

See similar textbooks

Similar questions

31. A uniformly heated square plate of 2 ft × 2 ft is exposed to cold air at 80 F. The heater output remains at a constant value of 1 kW. Air, at atmospheric pres- sure, flows over the plate at a velocity of 16.5 ft/s. Find the average temperature of this plate. [Ans.: - 513 F].
Under what conditions may one describe atmospheric processes using the incompressible form of the continuity equation?
A one-third scale model of an airplane is to be tested in water. The airplane has a velocity of 900 km/h in air at −50°C. The water temperature in the test section is 10°C. The properties of air at 1 atm and −50°C: ? = 1.582 kg/m3, ? = 1.474 × 10−5 kg/m·s. The properties of water at 1 atm and 10°C: ? = 999.7 kg/m3, ? = 1.307 × 10−3 kg/m·s. In order to achieve similarity between the model and the prototype, the water velocity on the model should be (a) 97 km/h (b) 186 km/h (c) 263 km/h (d ) 379 km/h (e) 450 km/h
The velocity profile in a circular pipe of radius R = 10 cm is given by: [¹-6] U (r) = Umax where Umax = 20 m s-¹ and r is the radial coordinate, with r = 0 representing the center axis of the pipe. The working fluid is ethanol (μ = 0.001 095 Pas, p = 789 kg m-³. Determine the following: (a) The volume flow rate. [0.489 m³s¯¹] (b) The mass flow rate. [386 kg s-¹] (c) The average velocity. [15.6 m s-¹] (d) The shear stress at the wall of the pipe, if: du t(r) = μ¹ dr [-0.0767 Pa] (e) The dynamic pressure in the pipe, calculated using the average velocity. [96 006 Pa]
The continuity equation of fluids describes the property of energy conservation; and Bernoulli's equation indicates conservation of mass. Ture OR Fale
The SR-71 Blackbird, which is 107 feet 5 inches long, is the world’s fastest airplane. It can fly at three times the speed of sound (Mach 3) at altitudes of 80,000f t. When it lands after a long flight it is too hot to be touched for about 30 minutes, and is 6.0 inches longer than at takeoff. How hot is the Blackbird when it lands, assuming its coefficient of linear expansion is 2.4 × 10−5K−1 and its temperature at takeoff is 23oC?
(1) Given the working form of the Bernoulli equation as dW - F dm Where 5 is the friction heating per unit mass dQ F = Au dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F = = -gAz = Q Ax u 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer
1- Consider single-phase fluid flow in a 1-D horizontal reservoir.The reservoir is discretized using four blocks in the x-direction. A well located in block 3 produces at a rate of 400STB/D. All grid blocks have Ax-250ft, w-900ft, h-100 ft, and kx-270md. The FVF and the viscosity of the flowing fluid are 1.0 RB/STB and 2cP, respectively. Identify the interior and boundary blocks in this reservoir. Write the flow equation for block 3 and give the physical meaning of each term in the equation.
An airplane is flying at a velocity of 150 m/s at standard sea-level conditions. The temperature at a point on the wing is 270K. What is the pressure and velocity at that point? For air, C, = 1008- %3D kg K
Consider a Lear jet flying at a velocity of 250 m/s at an altitude of 10 km,where the density and temperature are 0.414 kg/m3 and 223 K,respectively. Consider also a one-fifth scale model of the Lear jet beingtested in a wind tunnel in the laboratory. The pressure in the test section ofthe wind tunnel is 1 atm = 1.01 × 105 N/m2. Calculate the necessaryvelocity, temperature, and density of the airflow in the wind-tunnel testsection such that the lift and drag coefficients are the same for thewind-tunnel model and the actual airplane in flight.
QUESTION 4 Cold air at 5 °C enters a 12-cm-diameter 20-m-long isothermal pipe at a velocity of 2.5 m/s and leaves at 19 °C as shown in Figure Q4. Take the pressure of air 1 atm, i. estimate the rate of heat transfer to the air, and ii. calculate the surface temperature of the pipe. T, Air 5°C 12 cm 19°C 2.5 m/s 20 m Figure Q4
The actual car will be running at V= 35 km/h at p-1 atm and T=0°C (the air density and viscosity are 1.292 kg/m3, and 1.338 x 105 m2/s, respectively). A one-fifth scale car model is being tested at the wind tunnel at 198.3 km/h at 1 atm and 20°C. (The air density and viscosity are 1.204 kg/m³, and 1.516 x 10$ m²/s, respectively). The average drag force on the model is 50 N. What is the drag force on the prototype? Note that dimensionless drag is Cp 1/2pV² A O 41.8 N O 50 N O 15.0 N O 44.2 N O 8.4 N O 38.9 N